Black True R Carbon Fiber Vinyl Wrap Roll with Air Release Technology (20ft x 5ft)

Nice quality. First time doing it and definitely not perfect could have done better. Overall I am happy with. Heat gun is your friend but don't over do it. The vinyl is high quality. I was able to stretch it easily with the heat gun. Give it a nice heat bath after all wrinkles and bubbles are worked out to ensure it stuck down.

A bit thicker than I expected, also very quick to stick. I had a bit of a wrestling match with it before it ripped, it could have been to warm in the shop, not sure, but it didn’t light tack as was described. I’m a bit of a newcomer to large roof sized vinyl, but that’s my take.

Alright, let me start with saying that this is my first time wrapping anything. I don’t even wrap gifts lolWith that being said, I am completely amazed at how good this came out. Like, I really can’t believe I did this myself!I was very hesitant at first, but with a few DIY videos for tips..I’m extremely happy with the outcome.The negative reviews here talk about the adhesive, the vinyl becoming brittle, the vinyl getting wrinkled, but literally all of that could of been fixed with a handy dandy heat gun. Even a hair dryer.Some tips I learned and wish I could’ve read here were:- CLEAN YOUR ITEM THROUGHLY A simple wipe down with a microfiber won’t do the trick. Isopropyl Alcohol or clay barring will remove contaminants that would affect how well the vinyl sticks. Especially towards the edge or where you come to a fold.- ALWAYS USE A LITTLE MORE FROM YOU NEED once you measure out how much you need, cut off an inch or two more. This will help when you come across wrinkles, air bubbles, or “fingers” (big long wrinkles you can’t squeegee out) the extra vinyl, make it easier to pull up on your vinyl to squeegee anything out. It also helps when you pull on your vinyl, it prevents possible tearing. Also it gives reassurance that you’ve cut enough to be able to wrap properly around your edges folds or creases.- A HEATGUN/HAIR DRYER IS YOUR BEST FRIEND Use minimal heat. It helps if you pre-heat your vinyl before applying it to your object. It will become soft and stretchy so that when you apply the vinyl not only will it stick better but it will also become flexible and take the shape of your object. (Like curves, lines, etc) also, when you’ve come to an edge, applying heat there will cause the vinyl to naturally fall over the edge and will stick better.Did your vinyl get brittle? Apply heat!Did your vinyl get wrinkled? Apply heat!Do you feel like you didn’t cut enough and won’t be able to wrap around the edge? Apply heat and stretch!- DONT BE SCARED TO PULL OR LIFTThis is very durable material. But also don’t go to the extreme and over stretch.-KEEP A CLOSE EYE ON HOW VINY IS BEING APPLIEDIf an air bubble appears where you’ve just applied vinyl, it’s easier to pull back and work the bubble out, than to finish your wrapping and seeing an air bubble you missed located dead center on your object, making you basically unwrap your object halfway to get that bubble out Because you know it’ll bother you.You can use an old credit card or gift card (wrap the edge you’ll use with electrical tape to prevent scratching) or squeegee to assure the vinyl sticks to the entire surface. This also prevents air bubbles.- DONT FORGET TO POST-HEATOnce you’ve finished wrapping, apply heat to entire area you’ve wrapped. This is just as important as prepping the area you’re about to cover. Post heating will prevent the vinyl from trying to pull back and go back to its natural form. So with post heat you’ll know your wrap won’t lift or curl back. This is best with the heat gun, a hairdryer might be too weak for this one.I hope this helps! Enjoy!

1st time working with wrap and it's definitely not a professional quality install....but it looks pretty darn good from a few feet away. I had to do a lot of repositioning and when all was done it was stuck down really well. I was able to work out little bubbles with the squeegee. I did crease it in a few small spots and I royally screwed up wrapping over the edge near the windshield....but otherwise it turned out pretty good. 4X5 feet of material was perfect for the hood and I had some little pieces leftover that I put on the door handles. I did use a heat gun on the edge when wrapping it around the backside, that seemed to help a little. Otherwise just scissors, a knife, and a squeegee. I used magnifying glasses for trimming the door handles and a super sharp pointy knife....kinda scary initially but after a bit putting the knife on it wasn't too bad. It cost 30 bucks and was totally worth it, how long it lasts remains to be seen but it made the car look a lot different (you see white model 3's like....everywhere right?) Might have to wrap something on the wife's car now LOL!

I used this on the cowling for my motorcycle last summer. The look is is just what I wanted and it has stood up to a couple of thousand miles on the bike with no problems so far. The install was not difficult as I used a heat gun to form it over the curved part of the cowling.

I bought this to wrap my kid’s downhill bike. It was not easy to put on a mountain bike frame by any stretch of the imagination-but if you’re willing to be an absolute slave and do anything to make your kid happy-you won’t be disappointed by its longevity. Getting the air bubbles out and making the cuts to allow for such tight angles was not easy, but I made it work. If I still had the bike I’d take a pic to show you. He rode it half the season on whistler mountain in the bike park in expert level bike camp twice a week. That wrap held up better then the original paint did! Not to mention it looked cool, according to his buddies. I’m pretty sure it was the main reselling feature! Recommend you buy the spray to help install the wrap. And I recommend this wrap also.

For someone looking for a good interior or exterior vynl wrap at a good price this is amazing. Not too thick, can be stretched, self heal, good adhesion and looks amazing; not too glossy or matte looking.For the price. Quality is excellent. Better than those other non gloss "premium" vynl wrap

No le doy 5 estrellas por que no es tan adherible, en molduras pequeñas es complicado ya que es rígido a pesar de usar la pistola térmica, es demasiado propenso a rayar se incluso con la herramienta adecuada pero al final estoy contento con la compra y la recomiendo.

This roll was enough to wrap my interior trim on a f32. Only thing I would recommend is finding a role that is longer the 1ft as the center console is longer than 1ft, but two cuts of the material line up perfectly so you can work around it. Sticks very well, can be worked easily with a hairdryer, no bubbles no creasing.

Great product, love it