Cutting NOT Required - 2 Key Fob Keyless Entry Remote Shell Case & Pad fits Honda 2003-2012 Accord / 2006-2013 Civic EX / 2009-2015 Pilot /2005-2006 CR-V

Key broke out of the original plastic housing so I ordered this and it worked great. Installed it following the instructions and it feels more sturdy than the original. Everything fit great and it looks great too.

Got this for a 2005 Accord key where the plastic around the metal blade had started to crack badly. I expected this to be a very quick install, but it ended up being a lot more involved than I expected. Not surprisingly, the instructions are very limited - here are some things I found that I hope you may find useful. 1) Your old metal blade may be very hard to remove from the old key housing. In my case, since it was already cracking around it, I was able to snap it out, but if the housing wasn't damaged around the blade you may need to use side cutters to cut the plastic off around it. Trying to lever the key out of the housing may result in bending it if the plastic isn't already cracked - so be careful. 2a) If you have a transponder (I did! See the first and second photos) you may be in for a wild ride figuring out how to deal with it. To start, it was incredibly difficult to remove, in addition to being press fit into the top plastic shell with a little cap over it, one end had a small blob of glue holding it in place. I ended up needing to cut out the plastic around it with an x-acto knife to free it. 2b) Once the chip is out, there's no way to mount it like in the OEM key, just a space where it can go. It will definitely rattle around, and if the key ever cracks open for any reason it will almost certainly be lost - meaning you won't be able to start the car. I ended up using two little blobs of hot glue, one in the bottom of the spot where the chip sits, and then one along the top edge of the remote unit. If you choose to use glue, make sure you use a glue that can be removed! I almost used epoxy but then realized I would never be able to get the remote out to change the battery! Hot glue will keep it from rattling around inside, but then can be peeled off later when it's time to change the battery. 3) The plastic frame that slides over the blade fits VERY snugly. If you have any crud on the blade, especially around the bottom, it will have a hard time going down. Clean the blade with an alcohol wipe or similar to get around this. Once it's clean, note the orientation of the frame to the blade, there's a taper at the bottom that should be clear, then pull the frame down with even pressure one each side. The hole in the blade may not perfectly align with the holes in the frame. Mine still ended up going together just fine despite this, but be aware of it. 4) The blade/frame piece does not float between the two halves of the housing, it mounts into the back half. There are grooves it will slide into, then click into place. Again, if you look closely, it will be intuitive. 5) The halves hinge together from the back of the housing, at the key ring slot. 6) Do not over-tighten the screw - if it's not going in smoothly, take it out and make sure it's aligned well. Once it's all the way in, don't "torque" it down - you'll either snap it in half or strip the threading in the housing. This is a good product at a great price and I expect it will hold up well, but take care when assembling it or you'll end up buying another one.

2013 Honda Civic SI This works great as an inexpensive replacement for the key fob. I broke my plastic oem key fob, right on the key-ring-attachment loop. I tried to glue it back together, it kinda worked, but looked pretty budget, and I could no longer change the battery in the fob, and then the glue failed, and it broke again, worse than before. I was sad. then I saw this, and thought that it was worth a shot, and it totally was. Very easy to take the necessary parts out of the old fob, and transfer to the this one, and it all fit well, and works perfectly well. I am no longer sad.

It works great, fit great. Only issue is it only lasted a little over a year before the plastic broke. It takes just a few minutes at most to swap them out (for 8th gen civic at least) and I bought the 2 pack for $10 so its not that big a deal. I also am a gig driver so I'm always fumbling with the keys all day long every day.

Exactly what I needed. My key fob had been broken for a long time, and I already wasted over $30 on a low-quality replacement from a local auto parts store. The fob still worked, but it was falling apart. I came across this solution and within 3 minutes my key was back to working like new on my 2007 Civic Si. Simple, fast, and actually worth it.

Great choice if your key fob is broken. The kit came with a small screwdriver, which made disassembly and reassembly easy. The housing fit together properly, all the buttons lined up correctly, and everything worked as it should after assembly. The finished product looks good and feels solid, not cheap or flimsy. Overall, I’m very happy with the outcome and would recommend it as a cost-effective replacement.

Buen producto aún no lo he instalado. Gracias

Me sirvió muy bien solo le haría falta el logo de Honda para que fuera perfecto

Cette coquille permet de retrouver le plein usage de la clé et nous fait ainsi épargner beaucoup d’argent. Il est facile à utiliser et nous redonne une clé neuve.

El producto resulto 100% compatible para restaurar la llave original de mi Honda Civic 2012 Sedan. No tuve ningún problema para realizar la,sustitucion de la carcasa original rota de mi llave por la nueva. Solo fue necesario hacerle un poco de limpieza a la parte metálica de mi llave, ya que tenia algunos residuos adheridos. que dificultaban el armado.

Llego rápido y la verdad muy fácil de instalar la llave, el material se ve de buena calidad. Lo único que le faltó es el logo de HONDA en la parte posterior pero fuera de eso todo excelente. Y el destornillador es un plus.