HitLightsLED Strip Lights 3 Pre-Cut 12Inch/36Inch LED Light Strip Flexible Color Changing 5050 LED Accent Kit with RF Remote, Power Supply, and Connectors for TV, Home, DIY Decoration

The media could not be loaded. Great price, quick delivery, what’s more the quality and performance of the LED light strips are awesome!The Product comes with:1- [1] 360° RF remote controller2- [1] 12V DC power supply3- [3] Pre-cut (12 Inches each) 50/50 LED Strip lights4- [3] extension wires (12 inches each)5- [6] (4 PIN) male connectors to connect to the (4 PIN) female strips and the extension wires.6- [6] Adhesive backed wire clips to help secure the extensions in place when turning the corners.Even if you’re not a tech savvy person, you will be able to install the LED lighting strips with very little effort. I installed my lights in less than 5 minutes. Just plug the male 4 PINS into the female 4 PINS lights and extensions, test before installing onto your TV or Monitor to ensure you have both arrows connected in the right directions and the lights turn on correctly. (If not, then check to ensure the connection is not reversed.) Then just remove the LED Light backing and affix to your TV, and plug in.The LED lights on the back of the TV creates a stylish aesthetic experience that both enhances the room’s ambiance, but most important makes your eyes feel less stressed while watching TV.The 360° RF remote controller controls the lights, which is accessible from across the room. I was able to turn on the lights from my upstairs, about 50 feet away that beats any other RF remote I’ve had in the past. Also was able to enable the different lighting functions like; changing colors, sequence mode, speed of chasing patterns, dimming lights, using the various scenes, etc…without any interference or having to find an ideal location to make it work.The process is the same whether you are installing onto a TV, Monitor, under a Desk, or Table Lighting.HitLights customer service is very quick to respond if you have questions, and their follow through is exceptional.I would highly recommend this product. Thanks for taking the time to read the review and hope you found this helpful, if so give a thumb up by clicking the “Helpful” button below. Cheers!

I use these on my 5 shelf bookcase that I actually use for my spices and seasonings and they light everything up nicely!

I purchased this to increase player visibility on a two-keyboard performance setup. I stuck the strips to the underside of the top keyboard, to shine on the bottom keyboard (and to give my keyboard rig a little visual "oomph").Pros:Very affordable, and VERY easy to apply; so far it's survived set-up and take-down for a couple of gigs. i haven't had the lights in service long enough to comment on the robustness of the adhesive. PAY ATTENTION to the positions of the little arrows on the connectors. If the arrows aren't lining up, you're going to get unusual results.Cons:The remote is unintuitive, as is the manual. Sincerely, just dork with it and you'll figure it out. The power supply cable is quite short. The power supply connection to the LED strips is VERY fragile - just a tug and the lights go out; OTOH, it's equally easy to reconnect. One might consider some kind of strain-relief to prevent blackouts.For the life of me, i can't tell the difference between "modes," on the remote, but since i personally don't need an ever-changing light show on my rig, it's not a big problem. You can have steady lights, or sequentially color-changing/flashing lights; take your pick.For the price point, it's a great deal, IMHO.

DO NOT ATTEMPT THIS MOD WITHOUT ANY SOLDERING SKILLS AND SOME ELECTRONIC CIRCUIT KNOWLEDGE.I've been installing LEDs in guitar amp heads for many years and have watched the improvement in designs making these mods so much easier. Most of the LEDs kits are the same, but I really like these Hitlights. Nice and bright with the standard remote included for changing colors, patterns, and speeds. I like how the strips are a bit flexible and really like the adhesion option. Just peal off the back of a strip - I was able to install 2 strips inside the amp head and they seem to be holding excellently. I hardwired the LEDs 12 volt power supply to the AC leads inside the amp head that feed the amp's power switch. This enable the LEDs to come on when the amp's power switch is turned on. Again, please don't attempt unless you know what you're doing. I've seen some amp heads where they ran the 12 volt adapter outside the head and plugged it in separately into a power source just like the amp. This results in 2 AC cords coming from the amp which is OK and much safer, but a little inconvenient if you don't know how to connect to the amps power switching. The rest of the LED wiring rests inside the amp head where there's usually plenty of space. I only do solid state amp heads because of the available space. Fifteen years ago, I was one of the few techs doing this LED mod, now, with tube amp heads, the manufacturers often design a LED element to illuminate the inside of the head showing the powers tubes and such. LEDs make this possible because they don't get hot and run on very little voltage.You'll notice in the pictures, that I Velcro the remote onto the back of the head. Can't lose it - it's the only way to control the lighting. Rock On!