DEWALT Tool Organizer, Tough System (DWST08205)

The engineering in this system is superb. As an engineer myself I can appreciate the dozens of little details in the system that had to have taken a lot of thought, time, and prototyping. First of all, the stackability. The boxes not only stack, but firmly fall into place so they don't slide off. They also lock together. On cases with a lid, a convenient recess for placing a label tape is visible even when stacked tightly. Of course, stacked and locked together is great for transportation, but not for day to day use. This is where the racking system comes into play. Dead simple to assemble and very sturdy. I will say that that carrier brackets gave me a lot of trouble until I realized it was all operator error. Using the wrong tool for the job. It is difficult to get the bolt to engage the nut with an Allen wrench, even a a good size t-handle wrench. However, a Allen bit on a 12 inch extension bit attached to a drill does the trick with no problem - it allows you to hold the bracket in place with one hand and drive the bolt home with the other. So as I say, this was totally my issue and not the bracket design. I would like to see one small design change here, however: Graduated markings on the square tubing to allow easy alignment of a pair of brackets would be great. A tape measure works, but takes time and is difficult to manage while holding the bracket in place. If I was to build these again, I would lay out all the square tubing together and mark them with a framing square. I have the small, medium and open tote cases and they are all great. I want to comment specifically on the small case though. It is an amazingly flexible case. You can leave all the plastic organizers in it and store small tools/parts, or remove some or all of them. One of my favorite features are the groves in the lid that catch the edges of the organizers - this means if you configure a case with only some of the organizers installed they are still captured securely and don't slide around - no matter where you place them. I have also found the small bins built into the lids to be helpful. These bins fold down and fall into slot molded into the edge of the case, which props the lid open and allows you to access the two bins without needing to hold the lid open. One of the bins is has no dividers, and the other is divided in to smaller sections. The case has handles on the sides, front, and top making it easy to cary anyway that is convenient.

I recently purchased two of the DeWalt Tool Box Tough System Extra Large DWST08204, and I am beyond impressed with its exceptional quality and durability. This toolbox is a complete game-changer for anyone in need of a reliable storage solution. From its sturdy construction to its spacious interior, this toolbox has exceeded my expectations in every way. First and foremost, the build quality of the DeWalt Toolbox Tough System is simply unmatched. Constructed with high-grade materials, it feels rock-solid and can withstand even the toughest of conditions. Whether you're a professional tradesperson or a DIY enthusiast, this toolbox will keep your tools safe and secure for years to come. Moreover, the spacious interior of this toolbox is truly impressive. With its extra-large size, it offers ample storage space for all my tools, accessories, and even some larger items. The removable trays and customizable compartments are a great addition, making it easy to organize and access everything I need quickly. Plus, the robust latches and handles ensure hassle-free transportation, even when the toolbox is fully loaded. In conclusion, the DeWalt Tool Box Tough System Extra Large DWST08204 is a must-have for anyone looking for a reliable and spacious toolbox. Its outstanding build quality, ample storage space, and user-friendly design make it a worthy investment. I highly recommend this toolbox to professionals and DIY enthusiasts alike.

Have used this cooler for quite a few years now. It stays in my work van. During the middle of Texas summers, it holds ice for about 2 days with frequent opening and stocking with room temp or warm waters. My boss has a Yeti that’s about the same size and I would say that this cooler performs similar for around half the price and it locks in with my Toughsystem boxes.

If you transport tool, then these boxes are great. They are lockable, and waterproof, so they can be tossed in the bed of a truck, or used to store tools on a boat etc, with out worry. It also means they can easily be washed off. The boxes are sturdy enough for an average sized person to stand on with out them bending/flexing at all. They can certainly take a bit of a beating, handing bangs and drops. The handles (top and side) are comfortable to use and also sturdy. The latches open and close easily and have head up well over the past year+ of use. The clips on the side that hold multiple boxes together are the only part of these tool boxes I feel are a bit flimsy. DEWALT has changed the design of these. Both designs are thankfully compatible, and the new ones do appear to be tougher, but if you're using these regularly, or are not careful to close them when not in use, I could see them getting broken. (That said they haven't been a problem yet for me.) The hard sides allow the boxes to be stackable, and clips will lock them together, making transport with a standard dolly pretty easy, and storage either on the Dewalt toughsystem rack or just stacked or on shelves keeps everything tidy, but at hand. The Extra Large case is large enough to hold larger tools such as circular saws, or multiple tools. The Large case can easily hold two angle grinders along with backing pads, discs, and other such accessories, and have room to spare. Yes, they're a bit pricy, but are worth it. They'll hold up for a long time, keeping the contents protected. And if you compare them to other stackable tool boxes they're a much better product for a comparable price.

A few years ago my Dewalt addiction started with the Tough System tool box (the thinner one with the 2 drop-down trays inside). I was impressed with its durability and overall SOLID quality. Its still like new! I recently picked up this bigger tool box to go with it and as expected, its just as solid, just as durable and mates 100% perfectly with the previous purchase. I love that these products just snap together and are forward/reverse compatible with eachother. Dewalt has definitely earned a lifetime client in me. I'll be buying more of these in the future until I have a full rolling kit. Definitely worth the cost!

Perfect organizer for my screws and fits right in top of the tough system 2.0. Very sturdy and seals nicely. There has to be at least 50lbs of screws in it! Now I just need a brace for my back when I need to lift it again.

This a strong and sturdy rack really like it my tool box wont slide around in back of van. And real fast shipping. Tks

Tengo aprox. Un.año que compre la caja., y hasta el momento sigue como nueva, a pesar de que le he dado trato rudo. Me he subido sobre ella. (Y peso aprox. 100 kg. ) a resistido sin problemas. Se ha mojado se ha caído, se a enfrentado a la tierra y mantiene protegida y perfectamente seca la herramienta. Tiene buen volumen de almacenamiento, Le he cargado aprox. Entre 30 y 40 kg de herramientas, y las agarraderas han soportado sin problemas. Ahunque en algunos momentos si se sienten como que ya no pueden más. Pero han soportado. Los broches de metal perfectos. En fin. A mi parecer es una muy buena opción para mantener tu herramienta bien cuidada. ( a desplazado a otras 3 cajas que tengo, una craftsman, una stanley y una urrea. ). Se convirtió en la consentida. Les pongo algunas imágenes reales del estado de una caja con un año de uso y sigue con solo rasguños normales del trabajo.

اتمنا انت تكون اسعر المنتج لاتتغير بارتفاع 200%100 و اكثر . يكون الارتفاع معقول