TigerDad Rolling Laptop Table Lap Desk for Laptop Rolling Cart Tilting Overbed Bedside Table Overbed Desk Overbed Table with Wheels Adjustable Laptop Stand Sofa Side Table

This sturdy laptop table is worth the money! Assembly took about 20 minutes.Assembly: There is no how-to assemble video. All the tools you need come in the box in a bag. The instructions are pictures and pretty simple. I am not mechanically inclined and I assembled it by myself. It took about 20 minutes.The table does not fold for storage.The mouse table is 8 inches of the 23 inch wide table,The swivel hardware under the table that attaches the two tables hangs down 3 inches from the bottom of the table.A great feature is that the whole table swivels on the pole, so you do not have to move the table out of the way to get up. It swivels out of the way without wobbling.Mouse Pad Table: The mouse pad table is built for right-handed users. You COULD turn the table to be left-handed-mouse capable, but then the safety stopper would be behind the laptop instead of under it to keep it from sliding off. The mouse table portion of the table is where the table swivel is attached.The stopper IS a separate piece, but the attachment holes are only on the side as shown in the picture.Removable wheels? No. However, in the instructions, the wheels are the first thing that is attached. If you do not attach the wheels, there are no rubber feet. The metal frame would be on the floor possibly scraping your floorThe table was recently remade to keep the weight of the tabletop centered. It did not lean to the “laptop” side as I've read. There are TWO turn-knobs now to prevent lifting the whole table out of the swivel pole. Always keep the knobs tightened to prevent the weight of the table from tipping over.Can you tilt the whole table? Yes, you can tilt the whole table, each side has knobs to adjust it separately. You can align both sides to the same tilt, OR each side at different angles. It's great for a drawing surface. Tilt the laptop side for the artwork, and use the mouse-side flat for brushes and pens.

Was easy to put together, a bit heavy but wheeling it around works. Will say with the wheels it doesn't fit under my couch without me lifting the couch.This is good if your sitting, but not so much standing. Using this on my bed is great. Another issue one may find is, if you push too hard it will start to tilt.Something to be aware of too much weight, like a fat cat, it will tilt over so be careful.

This table can be used in so many ways. Personally, I like to prop myself up in bed before going to sleep and just look at some episodes on my ipad or browse online shopping (Amazon). I was holding the ipad up to my eye level with my arm and that was sure uncomfortable. The base of this table rolls and swivels, the desk part tilts from flat to eat on or write to any angle to hold a book or laptop, ipad etc. I get in bed, pull the table across my lap, adjust the tilt and read or shop or whatever. The directions SEEMED difficult because they show pictures instead of words but actually it made sense and the tools are included so I assembled it very easily. It is well designed and well made. I am very happy with it.

Oddly the pole that is intended to hold the table surface level and parallel to the floor doesn’t. You insert the pole (top pole attached to the table surface) to the base pole (attached to the base of the unit) which has two screw holes to allow you to raise/lower the top pole. But the top pole does not have corresponding holes. So despite tightening the screws on the bottom pole, eventually the top pole will descend into the bottom pole and the surface starts to tilt down to the side opposite the pole. You have to forever untighten the screws, raise the surface/pole back up to the desired height then retighten the screws. Serious flaw and instability issue.

I'm not always the most mechanically inclined so often worry about whether or not it's going to take me 3hrs to build. This IS NOT the case, the design is sufficient that by following the pictures, you can do the thing. The only thing that bit me was that I tried to insert the arm into the rings missing the fact that the last ring on the mouse rest portion needed to be installed last (because the joint isn't centered or in the middle.) But in the end it took me maybe 45min to put together nice and tight. The next one I could do in 10min.It's early on but the table is super sturdy, I worried that typing would be wobbly but that just isn't the case. If after a few months this changes, I'll gladly come back to update the review.The only "flaws" with it are that the tabletop is laminated MDF, but for the $50 price category are you expecting hickory or walnut? The drawback here of course being that I can imagine the edges being worn smooth after a few years of use. No big deal here.The height is important for me as I wanted to be able to stow it under my workstation desk that includes a sliding tray for music keyboards, so I needed something that would go under 23", and this was one of the few that could accommodate that. It works, and also, the telescoping neck is sufficient (doesn't use a hole mechanism to lock) to get at exactly the right extended height quickly that it can nestle easily in the space above the synths but not touching the top of the desk. (See photo)But I have to stress, for as low a price as we have, the sturdiness of the construction is definitely chef's kiss.