USB 3.2 to 5GbE Adapter (WP-UT5) Realtek RTL8157 Wired LAN Network Connection 5G, 2.5G, 1G, 100Mbps

The previous review that stated it might work or it might not depending on hardware is spot on. Go read it if you haven't already. I am primarily using a M3 MacBook Pro 14 and this adapter consistently gives the max speed/throughput my ISP says I should be getting (2Gbps up and down). This is the fourth USB-C to Ethernet adapter I've tried but the first with the more advanced Realtek chipset, and that seems to make the difference.I have tested this out on a 2019 16 inch MBP with an Intel CPU and that doesn't hit anywhere near the advertised speed ... HOWEVER it's a work computer using Zscaler and very well might be bandwidth capped. All of the other adapters I tried had me around the same speed as this adapter, about 6-700 Mbps up and down. I'm also on macOS 14.7 which may also contribute to the problem. I have an 13 inch MBP with Intel chipset from 2020 running macOS 15.5 and that gets the same speed as the M3 MBP. So, almost certainly an issue with Zscaler and/or the older OS.Haven't even talked about my network infrastructure. Using Ubiquiti router, switches, and access points and a Comcast XB10 in bridge mode. I have yet to test this on different network infrastructure, so that may impact things too. I know I often have trouble with multi-gig hardware on my Verizon FIOS 1Gbps network (which I keep to 10/100/1000 equipment, so I haven't even plugged this in on that Verizon network).Giving this five stars because it's the only one giving me consistent speeds I expect on the 2.5Gbps network. Your mileage will almost certainly vary, so be careful blaming the adapter if you have problems.

I originally wrote a scathing review of this thing, but I deleted it after doing more extensive testing. This thing can work well under the right circumstances, but that's something you need to be very wary of if you're thinking of buying it. The hardware you have, the OS you use, and the driver you're running all have to be just right for this to work well.Whether this will work for you is very much hardware-dependent. If you're planning to plug this straight into a machine with at least a USB 3 port, you might be okay. If you're planning to plug this into a dock or a hub, or if your machine uses an internal hub with other things on it, there's a good chance you'll have a bad time.As an example, I have a 16" 2024 MacBook Pro. Plugged straight into the machine with the right software (discussed below), using iperf3, I get consistent performance of around 4.7 Gbps in both directions. I also have a Dell S2722QC monitor, which has 2 downstream USB ports that nominally support 5 Gbps. Performance if I plug it into this thing is a total crapshoot, and I don't know why this is. Unplugging it and plugging it back in leads to wildly different results, sometimes with performance as low as 300 Mbps, other times exceeding 3 Gbps. Sometimes it ends up being poor in one direction, other times it's fine both ways. I can't make any sense of it, but it makes the device unusable in this configuration. It's also worth noting that a 1 Gbps Ethernet adapter performs at full speed in both directions consistently plugged into the same monitor, so I don't know what's going on here.Now on to the software side of things. On Windows, forget about it if you aren't using Windows 11. This thing is unstable under Windows 10. And even if you run Windows 11, you will need to update the driver from the one included with Windows to have a good experience. You can either install it from the Realtek website or run Windows Update after plugging it in. If you don't do this, it will only sync with your switch at 2.5 Gbps, performance will be very poor (worse than a 1 Gbps adapter), and you'll experience dropped packets.On macOS, I've seen people report good experiences with 14.5 and above, but I can say from experience that you will experience issues if you run 15.0-15.3. These problems appear to have been fixed in 15.4, which was only released a few days ago as of the writing of this review.I didn't do as much testing on Linux, so all I'll say is that if you aren't running a recent kernel, you aren't in for a good time.In summary, this might work for you, or it might not, and you probably won't have any way to know until you buy it. Personally, I'm on the fence about whether to keep it or return it.

This adapter gets hot and drops packets on a regular basis. Difficult to get file transfers done when you can't rely on the ethernet connection. My built-in 1G ethernet port on my laptop performed 100% better than this one. Shameful, to say the least. Not often I don't recommend a purchase but this is the exception.

I have this connected to my Mac Mini M4 through my TB3 dock. It is connected at 5Gb through my UniFi Aggregation switch via a 10Gb SFP+ module that can negotiate between 1,2.5,5 and 10Gb speeds. I did numerous iperf3 tests against my 10Gb server and had a consistent 4.70Gb throughput in both directions.So far I haven’t had any strange behavior.

As of 12/12/2024 this product is unstable with the latest Realtek drivers installed (Ver: 1157.16.20, Dated: 2024/12/06) on a Windows 11 system. Device works for about 5 minutes then it will reconnect from the host (USB Bus), upon automatic reconnection it does not reconnect to the network. Physically re-plugging the device is needed. During the times it was working, I was seeing ~3.6 Gbps down/~4.9 Gbps up (via USB 10 Gbps port). Hopefully future Realtek drivers resolve this issue. A Realtek RTL8156B based 2.5 Gbps USB NIC has been rock solid in comparison.Update: Appears that the supplied 'USB C to A' cable is faulty. When using the supplied 'USB C to C', the NIC does not drop from the host.

Inexpensive. Works great when using a USB 3.2 Gen2 port. No complaints!

Most 2.5gbit USB adapters are based on a similar Realtek chipset, but they are CPU hungry. I bought this to increase the network bandwidth available on an Intel N100 based mini PC. The CPU could not keep up to provide full 2.5 gbit speeds. This 5gbit card provides much better performance at 2.5gbit speeds on lower powered systems. Perfect for what I needed.

No me sirvió para lo que compre y tiene varias caídas no es estable .