Magigoo PC 3D Printer Bed Adhesive Glue for Polycarbonate Filament, 50mL

When I first started 3D printing every print was impossible to remove from the bed. No matter what I did it stuck to the bed and I had to pry and pry to get it off. I started using this glue and it's made a huge huge difference. People suggest all kinds of weird things (like hairspray which makes a huge mess overtime) to get your prints to stick and come off after printing. This stuff goes on clean and easy, becomes a little tacky when the bed is warm, and holds the print well. After the print is done I let the bed cool down and the print comes right off. You have to put it on when the bed is cold, and remove the print when the bed is cold for it to work best. Be patient and it will work wonders. The bottle looks small and it might seem expensive for the size, but it will go far. I'm 1/3 of the way through the bottle after using it for a month. I've printed dozens of items in the time, covering the entire bed each time. Most of the time I remove it after a print with 70% isopropyl alcohol to get a nice clean bed before each print and reapply. The manufacturer does indicate you can use a single application for several prints, which I have confirmed is true. But I'm OCD about keeping my bed clean so I clean and reapply after most prints, and I still likely have 100 or more prints left worth of glue. If you're more frugal with it than I am then you'll definitely get more prints. Shake it well before each use. When you apply turn it upside down (obviously) with the sponge side on the plate. Push down gently as you move the bottle around to release the glue, and make a nice even thin layer of glue. Sometimes a quick push is all you need to get the sponge wet and then you can just rub the glue around until it's covered the area you need. The reason I mention this isn't to state the obvious, but the sponge does get some wear and tear on it after a while. Fortunately, the manufacturer realized this and there is an extra sponge that comes with it. If you're having problems with either adhesion or removal BUY THIS RIGHT NOW!!! Skip the cheap glues (5 sticks for $5 deals), the hairsprays, and the other weird tricks and just buy this.

I have a prusa mk2 with a heated PEI bed. I've tried forever to print with polycarbonate (in particular polymaker PC max). The biggest problem was bed adhesion. Nothing would stick well...other than buildTak, but buildtak would adhere TOO well, so much so that it was nearly impossible to remove the print without ripping chunks of buildtak off with the print. This is obviously not sustainable because buildtak is expensive. Enter magigoo for pc. Holy crap. This stuff is magic. Even with buildtak, as much as it was impossible to remove the print, would still have problems with adhesion on corners of my print and lift/warp on long prints. Not so with magigoo. The entire print, no matter how long or tall or wide stays stuck the entire time, so no warping or lifting. And yet, it pops right off with minimal fuss after the print has cooled. I use the goo on the heated pei bed using built-in polymaker pc max settings in the prusa slicer.

I was about to begin the process of building an enclosure for my MK3S to help with the constant warping I was getting. I print a lot of mechanical parts with Prusament's PC blend, and they weren't usable due to the warping. Then I bought this $25 gluestick... THIS STUFF IS INCREDIBLE! I put a think layer down on the bed where I expect the print to be and it STAYS PUT! I could even print 1/8" pins standing up no problem. If you print with PC-Max, Prusament PC blend, or anything similar, this is a MUST HAVE to prevent warping and ensure bed adhesion.

I like this stuff but it is rather expensive. I've found it works good with regular PLA on PEI. I was delighted to see it substantially improve bed adhesion with the functional nylon gears I make. All my printing was done, including the PC MAX, on a garlolite sheet in an enclosed printer. Before, with those same conditions, my nylon prints would ALWAYS have some measure of warping with glue stick. With this stuff I was able to eliminate my rafts for a super smooth bottom and also get super flat gears. It worked great with my PC MAX too, but I can't comment on whether it was absolutely necessary as I didn't print without it for fear of ruining functional parts made from expensive filament.

I was having great success with other materials—PETG, PCTG, PLA, etc, I was having an under 50% success rate with PC because even with glue stick, the first layer was not sticking to the build plate. Even the prints that did work had first-layer issues, and success was a matter of getting lucky and not having the print head snag the curled edges. Even the small details like screw holes stick when using this. -Bambu 2HD -Bambu clear PC -Standard Bambu PC profile.

Got the magigoo for PC because I wanted to try printing polycarbonate, initially tried printing on my bare PEI bed and it was a complete no go. My bed only gets up to 110c and the PC was not sticking at all, literally just lifting off the plate super easily and prints failed during the first layer. Followed the directions for this magigoo and started my print, got absolutely fantastic adhesion and my print came out great! It was easy to remove from the cooled bed as well. I also did not clean my bed after applying this, it helped a subsequent PETG print stick very well and no issues removing that print from the bed.

The applicator is worn through exposing its inner workings after using about half the bottle. Otherwise this performs as expected.

I use magigoo at work for both of our printers. I do a lot of prototyping and also print small batches of parts for chemical systems we manufacture. Since we need parts that are chemical resistant I use polypro, Polycarb, PLA, ABS, GF filaments and more. If you have used polycarbonate before you know just how challenging it can be to get good bed adhesion. We tried many solutions but Magigoo has been far superior. It lasts for a few consecutive prints and when you need to clean your bed its water soluble so it comes right off in the sink. I highly recommed Magigoo, the PP version made the biggest difference in ease of printing for me, but they all work really well.

Después de haber intentado imprimir de 1000 maneras con Policarbonato, este ha sido el único producto con el que he podido hacer que la pieza se adhiera perfectamente a la base de impresión, ni con la típica laca nelly, 3dlac, dimafix, no había manera. El único punto en contra es el precio, por un botecito bastante pequeño el precio es bastante caro.

Impec pour impression type pc, pc/abs sur bed lisse

Great for PC prints. Used it with Bambulab PC-FR on P1S. Fantastic. Used it with Polymaker ASA. Wow, just wow. Almost 15h print of a large part without a single adhesion issue. And there was tension in the material. It released as soon as the build plate cooled down. The price is high, but it will last. Besides if a 500+ g PC/ASA print fails than the return will be even faster

I stayed away from these products for a long time thinking that they were just glorified glue sticks but that is simply not the case. We work in an indoor, shared industrial space and required something that wasn't a spraying fumes and worked for polycarbonate. It seems expensive for the amount that you get but it actually works better than any other PVA adhesive we used before, and it does go a long way. I haven't tested how far one application goes since we rely on a high success rate for our parts but so far 5 seperate prints seemed to all succeed and stick down well. Also worked for pla but the pla adhesive they sell is have the price and probably the way to go for that material

Ottimo prodotto che da il meglio se utilizzato correttamente. Piatto freddo, stendere il prodotto , accendere il piatto a 50 gradi e rimuovere l'eccesso con un panno che non lascia fibre. Ripetere l'operazione due o tre volte e poi il piano è pronto e utilizzabile per parecchie stampe. Se ne mettete troppo a piatto caldo oltre a problemi di offset rimane poi attaccato al pezzo. A mio avviso è da utilizzare solo con piani lisci sia in pei che acciaio o vetro, è inutile su piani ad alta rugosità. Il pezzo in policarbonato se avete fatto tutto bene si dovrebbe staccare a piatto freddo facilmente senza nessuno sforzo. Questo comportamento è dovuto principalmente al ritiro .