P003 Anti-Friction Engine Treatment - 1 Gallon

Hello I have been using er since around 1989 I first ran some tests to see what I thought my first test I drilled astarter hole about 1/2 way through a 1/4" pease of steal using a some what dull 1/4" drill bit with a light weight drillpress then I put a copple of drops of er on the steal and tried to drill further keep in mind dull bit light weight press but the drill went no deeper so I took a die grinder and was bearly able to scratch the steal I had a 1985 s10 blazer that i still have the power stearing was making some wineing noise so I put 1. Oz in the resavore and it stopped making the noise aprox. 200000 miles later and on its 2nd Moter it still works great and no noise. I have been using it for everything from snomoble gas mix to chain case car Moters trains rear difs I bought a1976 Chrysler boat in2010 it was'nt used much by the previous owner it sat a lot it ran pretty good and wide open I got about 2200rpm out of it but it started hard new plugs and gas some sea foam didn't help I dumped the gas refilled adding er I'm 55 my dad is 86 I had ran the Moter a little the day b4 going fishing the next day we went to unload the boat my dad hit the key not knowing what I had done the Moter started so fast he said he couldn't let go fast enough he said what did u do I of corse said nothing dad he said baloney killed it and hit it again then killed it again and said fes up. Not only does that Moter start and run like new we are now getting 3000rpm I've tried a lot of additives over the years but I could tell you many story's about er all good ones .ps I don't write reviews on anything this is my first and most likely my last er is a great product I would put it up to challenge any product of its kind keep it comming

I've used it for years mixed in two cycle oil then with gas for all my two cycle engines. I swear that it almost doubles th RPMs withou effort. My Four cycle engines have lasted over twenty years and still going strong. My air compressors or air tools don't wear out any more! Much cheaper to buy the gallon instead of the quart. And lasts four times longer.

Using this product saves you more in gas savings than the product costs to use. It also will save you more in maintenance costs over time. Your engine won't wear out. Plus it makes your engine run cooler and smoother with increased power and torque. Considering all that, you really can't afford not to use it. I've been using Energy Release for twenty years now and I swear by it. I even put it in my lawnmower. Great product!

This was recommended by my mechanic. I put it in the crankcase of my cars , the power steering on my truck was acting sticky and this helped.My brothers jeep power steering was acting up and ER fixed his problem. It's been in the cars for about three weeks and I've also noticed an improvement in the mpg. I think this stuff works pretty good!

I was a little skeptical about the manufacturor's claims, but this stuff really works. I added ER to my crankcase and transmission (111,000 on the odometer) per the rates marked on the container and started driving. I started noticing that my engine was running smoother and quieter by the end of the first tank of gas. The transmission was slower to improve because it got cold right after adding it. Sometime during my third tank I began to notice that the tranny was shifting more consistently and it now holds gear better at lower speeds. I'm planning to add ER to my transfer case and differentials at the next service interval. I'm expecting ER to help me get to 500,000 and beyond.

Love ER it does what it says. I've seen first hand of what ER does for a motor and gears. My dear friend Bill Weckman used it in his blown and injected 65 corvette , he held the fastest street legal car in the world record for many years

We have been using this in our automobiles for years. Works great!

off and on....bought another gallon recently. Serviced my 45hp tractor. Hyd. Fluid and filters. All fluid per container chart used. Cut about 7 acres. After about 5 hours of cutting the hydrostat noise was reduced greatly, the engine already a smooth daedong diesel just quietly hums along. The cutter was serviced with Amsoil 75w-90 and one ounce of ER. The cutter was so quiet had to keep looking to make sure it was running. Only the sound of vegetation being cut. The best part I noticed at around the 9 hour mark over two days is the amount of fuel consumed. a quarter tank per 2 acre cut was now down to half of quarter tank per two acre cut. It took several hours of cutting to notice the Hydrostat just got better, noise wise and shifting wise from lo-med-high range much easier. I would recommend this product especially with a fluid service to gain best benefit.