20 Pcs Bungee Shock Cord Hook for 1/4” Cord Rope

They work, I like them, trusting that they are durable. Purchased for use with 1/4" SGT Knots Marine Grade Bungie Cord. However, you have about 5 seconds to assemble the end before it becomes impossible to assemble and you are forced to cut the cord again. I do see in the instructions mention of "spray" and there is a suggestion to iron it. Who wants an extra step like that, and I am not even sure what that means? "Some cord sprays too much after your cutting, so they can't fit into the hook directly. You can iron the end of the cut to make it fit the hook" I tried several methods, flame, trimming. What I found works is have your tools and parts close at hand, scissor cut your bungee, and very quickly push the bungee into the connector. Be sure to pre mount the collar!

These fit my bungee cord perfectly, and my wake surf boards are once again secure.

Hooks work as expected with 1/4” cord. Cut cleanly and assemble as you go. The receiver end is disappointing however. Hooks do not fit in to the hole on the receiver, instead use two hooks.

Works great. Haven’t put any real weight behind it but worked for me

These bungee do an excellent job of holding your rods securely as you travel from spot to spot in your boat. Never worry about a rod bouncing out of your boat again.

These look a lot like what I had bought for a dollar a piece from a fabric store, so are a much better value, which motivated my purchase to try them out. I received twenty-hooks and eight eyelet ends versus the twenty and six advertised, so it is very nice the seller included extras. The good news pretty much ends there though. The fabric store sold this size ends for use with 3/16" shock cords, not 1/4". I am not able to fit 1/4" shock cords from Sgt Knots into these. I also have cord hooks from the fabric store which are meant to be used with 1/4" cord, and they are significantly bigger than the hooks from this listing. The inclusion of the eyelets made this listing very attractive to me. Alas, the eyelet ends are meant to be screwed down, i.e. not used with the hooks. The eyelet hole is not big enough for the hook to go through. I am not sure it's worth the effort and risk of breakage to drill the eyelet holes bigger so the hook can pass through. The shank of the hook is slightly smaller than the eyelet end, and the result is somewhat unsatisfying. The locking cylinder slides on and off easily on the hook, fortunately it does hold the cord in place when the ring is installed. However, I have some concerns about the locking cylinder being inadvertently slipped off (yes, it is that loose), at which point cord retention fails. The locking cylinder is difficult to put on the eyelet end. Strong hands or tools are needed to use the eyelet ends. The Knipex plier wrench I have worked great for pushing the locking cylinder onto the shank. These terminals do not meet the published specifications - I cannot use 1/4" shock cords with these terminals. I can theoretically use the hook ends with 3/16" cord, but then have failure concerns. Those concerns can possibly be alleviated by gluing the rings onto the shank during installation, which makes these non-reusable terminals. Strong value (quantity and variety of terminals included in the purchase price) saves this item and earns it a three-star rating.

These hook ends are surprisingly durable and reliable. Once correctly affixed to the ends of any length of stretch cord, they stay in place, wont marr surfaces, and are just large enough to grab any ring-type fastener. To hang onto larger hooks or rails, simply use the hooks to make loop ends that can go around almost anything. I use these to quickly stabilize my canoe atop my SUV, as well as for a myriad of other things in my home and shop.

I do NOT usually post reviews, as I feel most of them are fake, and most, like me, don't make decisions solely on them. In fact, I only leave reviews on the JUNK I catch! THIS ONE IS DIFFERENT! I have had a lot of unpleasant surprises lately with these types of items, but this purchase was SO GOOD, I had to be honest and let folks know. The circumference of ALL of the hooks mating surfaces were 0,356" +/- 0.001, if that! The ID of the collars was ALL 0.3575" on the money. They went on snug, but went on, even if pliers were needed to finish the install. THANK YOU! ONE great purchase out of a dozen from different companies makes, makes you my Go-To folks!

Works great and add a good price

Excelente de buen material.

Solide et très pratique !

Works well but you need a wife jaw pliers to bet the collar on. With such it is easy.

Facile d’utilisation et permet de maintenir en place les objets de notre véhicule récréatif lors de déplacement.