NP110 Non-Programmable Single Stage Thermostat, 4, 0.5

The wire terminals could be better positioned. The most logical way to route the wires would place them behind the temperature buttons - the ones you use are not part of the face, they must contact the actual buttons attached on the circuit board. It may be easier if you have only one thermostat cable, and not two (the air handler installer opted to add another cable rather than replacing the existing one). It was a simple install, other than the wire routing. The labels were helpful to mark the wires being used. I have found I do not need the backlight - all the settings seem to be easy to read. I would prefer that it not need a battery, but many models do. I was looking for an inexpensive replacement to our old, erratic mercury switch thermostat. I have found it to be reliable and accurate so far. It does audibly 'click' when operating, but so do many others - have not found the noise problematic. Other household items make noises as well. This thermostat displays both the set and current temperature at the same time. It also displays the current temperature when it is off. The cycle is not fine-tuneable (there is only one permanent modification available, meant for hydronic), but I have found it to cycle the system acceptably.

Works great!

If this wasn't so cheap, I would have only given it 3 stars. But the price and value bumped it up to 4. The instructions are... meh. But if you've done a thermostat before, it won't be that big of a deal. The only real problem is how the posts are oriented and labeled. Their openings are too close to the hole the wire bundle comes in. And the labels for the posts are between the posts and the hole! So as soon as you get your wires through the hole, it's a game of angles, flashlights, and STRONG reading glasses to see where they go. On top of that, getting the wires into the posts is a pain because of how close everything is. Tip: Use a small pair of needle nose pliers. Makes life a whole bunch easier! Happy to not have some annoying programmable thing. All I ever do with the programmable ones is set a temp and turn it on. The rest is just expensive noise. This thermostat does away with all that nonsense and just works.

I replaced my Nest E thermostat with this very simple and basic thermostat. Readings changed constantly on my Nest and the electrician said it was probably because of a neighbor with another Nest who was changing readings on his, via wi-fi. Way too much hi-tech interference into my home basics. Back to simplicity without outside interference with this very inexpensive replacement thermostat. Backlighting disable by default, setup is described in manual.

Very simple. I'm retired. Home every day. Get up, turn the temp up. Go to bed, turn the temp down. No programming. No wifi. Wanted simple. Simple is good. If this sounds like what you want, buy this unit. Simple follow-instructions. Lit read out easy to read with my glasses at night. As for the low ratings, this was my 2nd purchase. The first works great after 2 years. As for accuracy, got to laugh. Accuracy? Is it exactly 70 deg F? Doesn't matter. When I set 70 it feels like 70. Now, repeatability? Excellent. For $20? No brainer. Oh and, hook the white wire to the W terminal, red to the R terminal,...... Easy peasy. Oh (again), I have a gas, forced air system with conventional AC.

I found it so frustrating to try and install that I just gave up and ordered a different one altogether. Yes, it was more expensive (about twice as much $) but so much better. This product is low budget; cheaply made and cheap-looking and was impossible (well, for me, anyway) to get the wires from my wall threaded thru the (little slot in the) back and into the body of the thing and then immediately 'bent' 90 degrees and pushed into the appropriate little holes. Not enough room to work with — I already had short wires sticking out of the wall (my problem — not the fault of this thermostat, I give you that), but I found it just entirely too "tedious" to try and get the wires fed in thru the back (pushed through a slot, but it's not big enough to allow much movement of the wires coming thru), and then 'bent over' so those wires could then be pushed into the tiny receptacles of the thermostat. So, I then went ahead and spent twice as much on another brand and got a much, Much better product (easier to read, easy to adjust and easier to wire up)! I returned this 'Emerson' one to Amazon and immediately bought from Amazon a "Model 701" thermostat. It's also single stage, non-programmable, and lighted, but oh, SUCH a better product, and SO much easier to work with!! I had absolutely NONE of the problems with installing I'd had with this 'Emerson.' I sure can't recommend this. don't be a cheapskate and try to cut corners with this thing: I say spend a little more and get a better product! Jack in Colorado

This was exactly what I was looking for. The display shows you the temperature of the room and what the set temperature is. Some people had commented that you can't see it, but you definitely can read this display very well. I personally don't care for setting multiple temperatures, this lets you set the temperature and forget about it. You can easily adjust by pressing the up or down button to change the setting. I had my heating and air guy install it while he was doing my bi yearly maintenance check on my systems. It was a quick install. It is accurate. Very readable. I would highly recommend this thermostat.

This is a very basic unit with no temp offset, setbacks or scheduling capabilities Note that this is factory set in °F but can be mechanically modified to show °C

Easy to connect and controls well using the mv signal from the gas fire.

Technically it is not complicated to install, but the terminal strip is small and there is not much space to route the wires, making a bit challenging to get the typical rigid 18-gauge solid wires connected properly. You will need a Phillips size 0 screwdriver to fasten the wires in the terminal strip. There is a backlight, but requires a procedure using the up/down controls to enable it. The two required AAA batteries ARE included. Defaults to degrees F, can switch to degrees C by cutting a jumper wire on the PCB.

I purchased this thermostat in December 2021 to replace the original thermostat that came with my travel trailer. The original was Coleman Mach. See picture. After replacing it, the Emerson worked excellent. I can adjust the temperature degree by degree and is controlling it very good. It is a great product and worked excellent for my application.

Very easy to install , great value