BILITOOLS 3L Universal Brake Bleeder Kit, Vacuum Brake Fluid Bleeding Tool

I enjoyed using this. Made the job so much easier. Yes there are air bubbles being pulled from the bleeder valve. I thought i would have to bleed the brakes and clutch a second time after driving a little bit. Couple weeks now all good

Works really well and pretty easy to use. However, apply some grease to the quick disconnect fitting or you will have a hard time trying to connect the hose to the extractor.

Seems to work ok, though I am not positive air is not leaking into the line where the tube connects to the brake bleed valve on the caliper.

I had three vehicles to flush/exchange tbe brake fluid. Normally, I use a hand vacuum pump. They have the small resivors to collect fluid. Bilitools capacity - 3 liters. I didn’t dump it until all vehicles were done. Also included is a filler bottle that attaches to the vehicle’s brake fluid tank above the master cylinder. Ball valves control the pressurized airflow into the large waste tank. It’s full swing is 1/4 turn. About 1/8 turn provides plenty of vacuum. Attach the hose to the brake bleeder vave, twist the valve 1/8 turn to start the vacuum, loosen the brake bleeder and watch the old fluid get effortlessly removed. The hose the fluid goes through is super flexible, but does not collapse with vacuum. It’s not crystal clear, but it’s quite easy to see when the new fluid begins to come out. The bottle that attaches to the brake fluid tank holds a liter of fluid. I found it’s more the sufficient to suppy new fluid without using it all. Your will need to determine if it’s enough for yours. The bottle is supplied with a 1/4 turn ball valve to allow the fluid to flow. It also has a clamp to hold the bottle in your brake fluid tank. The neck of the bottle should extend below the fluid in the tank. Open the bottle. The fluid will fill to the level of the neck. If I had been diligent and wore the nitrile gloves all the time, I wouldn’t have had to wash my hands. I didn’t spill any brake fluid (old or new) and got maybe a drop on my fingers. Emptying the waste fluid was easy. There a non threaded removable cap/stopper. Also notable is how well the top to the waste resivor tank is made. It extends down the side to ensure a good seal, it’s held on by 10 or 12 screws. There’s no needto remove it. My opinion is it’s a better desgn than just a flat top. It comes with a lot of adapters for fittIng onto the bleeder valves. I only needed one. It’s easy to get all the fluid out of the line by holding your finger on adapter and letting it build up vacuum and removing your finger. I plan to send one of these to my brother for his birthday.

Great tool. High quality item. Glad I bought it.

Worth every penny! Buy this and you won’t regret it, makes bleeding so easy and the end result is exactly what you expect.

I purchased the BILITOOLS 3L Vacuum Brake Bleeder Kit hoping it would make bleeding my brakes a breeze, but unfortunately, it didn’t work as well as I had hoped. The kit comes with a variety of adapters and a 1L refilling bottle, which is great in theory, but in practice, I had trouble getting it to work effectively with my brake system. It’s possible that the issues I encountered were due to user error, but despite following the instructions carefully, I just couldn’t get the results I was looking for. The suction didn’t seem strong enough to properly bleed the brakes, and I ended up having to resort to the old-fashioned method to get the job done. That said, the build quality of the kit seems decent, and it might work better on a different vehicle or with someone who has more experience using this type of tool. For me, though, it didn’t quite meet expectations. It is what it is.

I did the initial bleed with this kit. Then followed by a traditional bleed. Wasn't even necessary. Good Product..

Happy and satisfied

Excellent

Worked great! Bled my whole brake system for a full fluid change and my brakes have been solid and great since. Highly recommend

Vehicle workshop

It works but takes a while for it to draw out the old fluid.