Draw-Tite 76595 Class 4 Trailer Hitch, 2 Inch Square Receiver, Compatible with 2022-2025 Jeep Grand Cherokee, 2021-2025 Jeep Grand Cherokee L.

Draw-Tite's long standing excellent reputation for fit, strength and quality was well represented in this application. Installation without any drilling was a treat and went smoothly. The process of installation on my 2019 Colorado followed helpful comments by others that the bumper needs to completely come off for ease of the bolt up and wiring tasks.I would add that the bumper was not easy to free initially after all bumper attachment bolts were out. To free the bumper, I found a solution by backing out all four bolts holding the original GM cross-tube to the frame rails until the cross tube had dropped down from the frame rails and had about a 3/4 inch gap. The bumper could then be tilted/extracted such that it's end plates that side mount the bumper to the frame rails would come free off the ends of the cross tube bracketing. (The bumper sat nicely on the cross tube's original ball mount support without any bumper attachment bolts in place, so no concern for the bumper possibly falling free during all of that cross tube loosening.)Draw-Tite eliminated that cross tube bracket-end interference and provides washers to tape to the frame that fill in as shims the free space thickness where the new cross tube omitted the OEM's interfering cross tube bracket ends. You can fully bolt up and torque the Draw-tite hitch to the frame rails and afterwards slip the bumper easily in place.I used a long breaker bar with a chain link fence top rail tube section as a cheater pipe extension on it to break loose the two of the (four in total) bumper side-mounting bolts that my 90 degree air hammer could not get in to reach. It was a lengthy effort to back out those OEM-threadlocked bolts, but no heat was required, just patience and endurance.After many years of installing frame mounted hitches from several manufacturers and front-mount tow plate bracketing for vehicles towed behind motorhomes, it was a pleasure to still be able to purchase another Draw-Tite product that continues the high standard you expect from a trusted brand.

I purchased this to put on my wife's Colorado as a Christmas gift. The installation was easy and I only need my wife's assistance once during the entire process. I looks very good on the truck. Actually it looks OEM. We haven't towed anything with it yet but I do not forsee any problems when we do.

Fits perfectly, no problems at all. The instructions say it takes about 60 minutes to install, this might be for the dual exhaust. I have the single exhaust and I was finished in about 15 minutes. It is heavy, I recommend a floor jack if you don't have somebody to help you hold it while you put the bolts in.

It was a perfect fit for my 2019 Toyota Tacoma (4 cylinder). The installation went well and looks great!

Easy to install but the powder coating done on this is bad trust the do powder coating myself and this was bad done. It wasn’t out gassed correctly and no primer added to it. Other than it’s a sturdy product should work better on powder coating it.

Great product and install instructions! Fit perfectly on my 2016 Colorado WT.NOTE: The actual install time would have taken me about 5 hours if I were trying to do it like the average DYI person. Certainly NOT the hitch's fault that the bolts were incredibly hard to take off the truck then equally hard to get back on. The hitch holes were right where they needed to be. I needed my friend's repair shop, lift, and pneumatic tools to get the job done in a reasonable time.

Ok so I have a 2015 chevy colorado wt 4x4 that came with a bumper hitch. I needed to change ball size often for different trailers and so i decided to go with the receiver hitch to make that easier. The hitch fit good and was good quality.Tips - There are 8 big bolts and 2 small bolts holding the bumper and old hitch on. these will be rusted badly and you will need a long ratchet and a 21 millimeter socket for the 8 large bolts and the little ones are like a 12 or 13 mm. you should spray these through a hole in the frame area inside the rail to help with removal. These are in an area that is hard to access with a impact and they are extremely tight. they use some thread locker on them so hit them with a torch to free that up or it will be a tough battle. the 4 large bolts on the bottom were easy to remove with the large impact. the 2 center bolts have clips that will need to be put on the new piece. the old hitch ball has to come out before the bumper will come off.be sure to remove the wires that are attached to the bumper before removal. i used zip ties to reattach the wiring. i used a 3 foot 1" drive breaker bar to loosen these big bolts so get ready for some physical work if you tackle this yourself. Good luck

Absolutely horrible experience!!! Product was supposed to be delivered in the morning so I prepped my 2023 Grand Cherokee Limited by removing the rear facia allowing myself time to install the hitch they kept changing the delivery time saying it's still being delivered 10 pm rolls around no hitch.Hitch will be delivered today 215 to 445 not even close 6 16 pm finally arrived in a demolished box.Ok let's just put it on and move on....Ho to put it on and it doesn't fit rubs against the spare tire and can't set the bolts because of tire. I guess who needs a spare tire right?What a joke