8341 No Clean Flux Paste, 10 ml Pneumatic Dispenser (Complete with Plunger & Dispensing Tip)

Very good flux for BGA rework: - excellent for removing large BGA chips - excellent for re-attaching large BGA chips - although it is a no clean flux , to make the board looking good this flux is not the easiest to clean however not the worse - good for day to day smaller components re-work

Nice quality soldering flux paste in a easy to use splunger dispenser. The metal nozzle is a good size and lenght which aids in applying the right amount of flux. 8341 is a no-clean, halogen-free flux with non-conductive, non-tacky, and non-tacky residues, ideal for touch-ups and reworks, so does not require cleaning after use, (but i always clean after soldwriing with IPA regardless). Works well with both leaded and lead free solders. I would recommend and purchase again.

I've been using this MG Chemicals 8341 paste for electronics repair and hobby projects, and overall, it’s a brilliant product. It's truly a no-clean formula; the residues are minimal and don't need scrubbing off, which saves loads of time. It really does an excellent job of promoting good solder flow, especially on tricky, small surface-mount components, making the job much cleaner than trying to use a liquid flux pen. My only slight niggle is the consistency; it’s a tiny bit runnier than other pastes I’ve used, so you have to be careful not to push too much out of the syringe at once, otherwise it can get a bit mucky on the board. But for the price and the results it gives, especially on old or oxidised pads, it's definitely a top-tier performer in my kit.

Helps a lot when soldering. Good applicator.

MG Chemicals 8341 No Clean Flux Paste, Good flux, you get a good amount which will last in my case. The flux melted quickly and effortlessly. I would say with this stuff the consistence is good you have to push extremely hard in order to get the stuff out. This as most flux does leave behind a vapor so if new best make sure you use this in a well ventilated room. Overall its good quality flux, says no clean buts it always wise to clean up after using as it take a mere for mins.

I have wasted so much money trying all sorts of flux but I am extremely happy with this. When it arrived in the tub it was a bit solid, but a few stirs with a wooden stick got it into a nice sticky paste. My method is to dab a paint brush in it and then apply it where needed. Makes the solder flow very well. A bit pricey, but all flux is, and I love this stuff - will be ordering more.

Initially I noticed this flux was very difficult to push through the syringe applicator. The plunger is an awkward, loose fit into the main body and it took way too much force to squeeze out the needle. Once applied to the solder joint it didn’t seem to want to adhere to the board and preferred to stick to the needle and pull away. After reading some reviews that mention warming before use I thought i’d give that a go. I found the flux to perform much better. It becomes more towards a softer paste/gel and is much easier to squeeze out of the tube. I also liked how the flux behaved. If you work in a colder environment (hangar/workshop/garage etc) in a colder climate then i’d suggest this might not work for you, unless you’re prepared to preheat the flux first.

The Best Flux Gel I have ever purchased. Not sure about the 'no clean' because it does leave a mess all over the pcb. Will buy more when mine runs out. Great for 0.5mm pin pitch chips.

It's very easy to put together and take apart to store. Great wetting and easy to use, though it takes a bit of pressure, so difficult sometimes with one hand. Does leave surface quite sticky, so I clean it off after to avoid dust build up and getting my fingers tacky. Cleans off well with 99% alcohol

Fa egregiamente il suo lavoro

J'ai récemment acheté la pâte de flux sans nettoyage de MG Chemicals et je dois dire que je suis très satisfait de mon achat. J'utilise ce produit pour le brasage de composants électroniques sur des circuits imprimés, et je dois dire que cela fonctionne à merveille. La seringue de 10 mL est très pratique et permet une application précise de la pâte de flux. J'ai été agréablement surpris par la qualité du produit, qui a permis une soudure facile et sans défauts. De plus, le fait qu'il n'y ait pas besoin de nettoyage après utilisation est un véritable avantage pour gagner du temps et de l'énergie. En comparaison avec d'autres produits similaires sur le marché, je trouve que le rapport qualité-prix de cette pâte de flux est excellent. Elle est un peu plus chère que certaines options bon marché, mais la qualité et la facilité d'utilisation supérieures en valent vraiment la peine. En résumé, je recommande vivement cette pâte de flux sans nettoyage de MG Chemicals à tous ceux qui cherchent un produit fiable et pratique pour le brasage de composants électroniques. La qualité est au rendez-vous, le prix est raisonnable et l'absence de nettoyage après utilisation est un vrai plus. Je suis très satisfait de mon achat et je n'hésiterai pas à réutiliser ce produit à l'avenir.

This is an excellent product, it is easy to use and achieves a good result with good solder flow.

This product is absolutely amazing not too much comes out when you're using it the size is disturbingly amazing for as little of a bottle as it is it does a lot and goes a long way there is no odor to it it's easy to clean up with a little alcohol is precise and the locations that you put it in and how hard you squeeze it doesn't allow you with the rubber stopper to pour out too much this is just a superb product