Creality Official Ender 3 Max Neo Glass Bed 3D Printer Platform, 320 x 310MM Tempered Glass Plate Build Surface for Ender-3 Max, CR-10 V2, CR-10 V3, CR-X, CR-X Pro, Good Adhesion Remove Easily

I'm a big fan of glass print beds for 3D printing because they are manufactured more flat (i.e. to closer tolerances) and stay more flat over their useful lifetime than do other print bed materials . When I recently purchased a reality K1 Max, it came with a magnetic flexible PEI steel sheet which seemed to be less than flat out of the factory and got less flat with usage. This resulted in high variances in my bed leveling mesh inconsistent first layer adhesion. This glass bed fits perfectly on a K1 Max with only two minor modifications. Specifically, you'll have to a) swap out the locator pins at the back of the build surface base plate for a couple of printed guide tabs and b) use low profile clips to securely attach it. If you prefer a glass bed, whether you're purchasing this for one of the older Creality machines that it was originally designed for or upgrading a K1 Max as I did, this is a quality product, perfectly suited to the task.

bought this for a Sovol SV-04 and it was a perfect fit. you'll need clamps for the bed though, be careful not to scratch the glass. flat and adhere-y enough for everything i've needed, even a year and some change in

Works great

This is a silicon carbide textured print surface with excellent flatness and nicely ground edges. Looks like the manufacturer hedged a little to avert poor adhesion criticism and painted the SiC surface with an additional ABS goo layer. Which becomes obvious when you try and deep clean it with acetone. I don't mind that because I normally use the opposite, smooth glass surface. But I wish they would add that detail to the product description just so folks don't freak out when trying to deep clean the surface. It's not a con, just a hidden pro :)

This works well. GREAT adhesion. Now, getting prints off? That is a whole other story. I would suggest this bed for hard to adhere prints, but possibly stay with the flexible plates that allow you to pop prints off if the model is delicate.

Perfect fit.

The glass bed was flat and even which fixed the low spot I have in the center of the default bed. Printing on it is very easy and my bed adhesion is fantastic. My only problem with it is that it might stick a bit too well

Wow level bed with no fuss. If you are fighting with a bad first layer I suggest using a glass bed

Decent enough quality for a glass bed, but I've given up and swapped to a magnetic plate as adhesion is either "none" or "pass me a jack-hammer this won't come off" with these. Honestly go buy a 3rd mag plate kit, they're way better.

Used this on my K1 Max, works perfectly with polycarbonate. The bed is very flat with a variation of only 0.3mm across the entire surface, used this as a replacement for my warped PEI bed.

Buy two of them so that you can start your second print while you stick the first one in the freezer for 20 minutes to remove your print. I've been 3D printing for years, and print mostly PLA on three Ender 5's along with other printers including Ultimakers. I've never had anything stick as well as the surface on this glass. Whoa! I destroyed my first print trying to remove it. Eventually I decided to place the bed and print into the small fridge/freezer in my back room. After about ten or fifteen minutes the print popped right off, no prying or scraping required. If you don't have some way of chilling the bed, I might avoid them... but if you do, then they work great. I am following my own advice and buying an extra one!

So much better than my previous destroyed stock Ender 3 V2 bed. However, within a day and a handful of prints a print stuck so well it pulled the coating off it.

I predominately print with LW-PLA filaments. The printed parts will not come off the print bed without destroying them even after putting the print bed in the freezer to cool. Perhaps this bed is better suited for hard to adhere materials but it doesn't suit my needs.