Geeetech TPU Filament 1.75mm, Shore 95A Flexible 3D Printer Filament with High Elasticity, 1KG (2.2lbs) Spool, Dimensional Accuracy ±0.03mm, Fits Most FDM Printers (Black)

You've saved my EcoReco (Patgear) S5 electric scooter. I print new rear tires to go on the hub motor ever since the original wore out at 300 miles or so. I've got over 1,000 miles on it and this has been the best material yet. My most recent attempt had been PEBA which was expensive. It seemed ultra promising, and gave one really great ride. However the PEBA deforms and stays that way with enough force. This meant that the perfectly tight wheel stretched onto one motor half then clamped by the other side rolled out and got larger around, sort of like rolling dough, until it was loose on the motor. I had ordered this TPU as a backup in-case that happened at less than half the cost. Well, it's the best performing TPU I've used for this so far! In-fact, I have over 100 miles on the printed tire right now and while some sharp rocks split it a little, it has basically no wear at all. It also hasn't stretched or loosened on the wheel. I chose clear orange since I always loved the bright orange wheels on the GoMotorboard 1500x and 2000x transporters I had. I got a clear type, specifically to maximize layer adhesion since there's no chalky pigment powder in the mix. I printed this on my massive delta printer 100% solid at 260c, no fan, no bed heat. I used 160% flow to compensate for the long Bowden tube. If you try this make sure to design a thin brim that prints on both sides into the model if you slicer only adds one on the outside. The TPU will shrink and lift a bit from the bed, so minimize that. The resulting tire is almost air free, nearly solid, and pretty damn indescribable. The spool has a very tangly look, but I had no issues with my 20 hour print despite the wiggly looking filament. It arrived perfectly vacuum packed with a desiccant packet. I did not dry it, yet I heard no crackles or other signs that it was wet despite me printing it at the highest temp my delta could go. The 95A is perfect for scooter wheels. It's not quite audible on the road, but low rolling resistance and fairly thuddy across sidewalk cracks. Perfect really when the focus is rolling efficiency but you don't want to sound (or feel) like a hard skate wheel the whole way. I had no clogs, no feeding issues, and again, it prints like a dream. This TPU had less shrinkage warping my large solid wheel than the Overture I used before too. I will be ordering more! Thanks!

Great color and print. The price is just right for the quality product. We love this filament and have bought other colors with this brand. The Tri color is beautiful for all builds! Makes things like a fidget cone look like we did 2 prints but it is all off this spool. Really a quality product that leaves us with a beautiful build!

Great filament!! Colors are pretty, worked great and didn’t tangle.

GEEETECH Filament Review Overview In the past, I’ve printed with Geeetech’s metallic pink and metallic blue filaments—both performed excellently and left a great impression. This tri-color silk PLA didn’t disappoint either; it continued that streak with ease. This review covers Geeetech Silk PLA Tri Color Filament (1.75 mm)—a coextruded blend of blue, purple, and black with a metal-like shimmer. I printed all test models on a Creality Ender 3 Pro, using settings that represent what most users might try out of the box, with only basic tuning. All prints were done straight from the spool with no drying. Test Setup • Printer: Creality Ender 3 Pro • Nozzle: 0.4 mm • Slicer: Cura 5.10.1 • Layer Height: 0.20 mm • Infill: 20% • Bridging Enabled: Yes • Bed Surface: Longer textured glass plate • Ambient Conditions: Approx. 24 °C, ~65% RH • Print Time: Approx. 2 hours Print Results Metric Observation Dimensional Accuracy Cube: X 20.15 mm, Y 20.12 mm, Z 19.92 mm. Cylinder: Ø 19.95 mm, Height 19.75 mm. Excellent tolerances for standard calibration pieces. Layer Adhesion Strong; models held up well under light flex and handling with no signs of delamination. Surface Finish Smooth satin sheen with mild reflection. The tri-color effect adds a premium look without overpowering detail. Bridging Clean on all spans of the temperature tower; consistent filament flow, no visible sagging or webbing. Overhangs Performed well on moderate angles—better than typical silk PLA in unsupported areas. Stringing Very minimal, even at 190 °C. A few faint wisps—barely noticeable and not an issue. Warping None observed across all models. Jamming No jams or clogs during the full print session. Odor None noticeable during printing. Pros • Excellent dimensional accuracy • Beautiful, reflective color transitions • Virtually no stringing • Great layer adhesion • Easy to work with right out of the package Cons • Silk finish can obscure fine details under certain lighting • No resealable bag included in packaging Tips & Tricks • Ideal Temp: 215 °C worked best across test models (but may vary by setup) • Bridging: Enable it for best horizontal performance • Retraction: Basic retraction settings were enough—no special tuning needed Images 1. Temperature & Bridging Tower – Shows consistent bridging across all levels 2. Classic Rook – Clean crenellations, strong vertical structure, and smooth layers 3. Calibration Set – XYZ cube, cylinder, and rook for scale and detail comparison Final Verdict 5 / 5 stars. Geeetech’s tri-color Silk PLA exceeded expectations in both aesthetics and performance. It printed cleanly, stayed within spec, and delivered models with just enough shine to stand out without compromising function. It’s a solid pick for anyone looking to add both style and reliability to their prints.

I haven’t had many issues with pla silk but this stuff is pretty difficult/brittle to work with- at least the green and yellow silk. I’ve attempted to print several dragons now on a p2s and the main issue I’ve had is with the supports. They keep breaking off halfway during the build, this stuff seems extra brittle. I ran it through an ams with 8% humidity, waited 24 hours before printing just incase it needed to be dried out, still issues, ran strong tree supports, it still failed. Finally decided to infill the supports so they wouldn’t break and my 7 turned into 9 hour print, had a support break near at the end. I don’t know what else to do except make solid supports lol. Yes I ran calibration on the printer and on the filament itself. Slower speed, tried that too. I have other ideas but I’m not willing to increase print time anymore when the normal pla silk i typically use prints great without the extra fuss. The only issue is I couldn’t get this color combo with the brand I typically go to so I tried this one :( with this all said, this stuff is probably ok with something that doesn’t need supports.

The Geeetech Silk PLA Filament in Red Black Ombré is such a beautiful filament! I love the unique color transition and the shiny silk finish it gives my 3D prints. The ombré effect creates a really eye-catching look and adds a special touch to finished projects. The only reason I’m giving it 4 stars is because it can be a bit finicky to work with. You have to make sure the filament doesn’t get twisted or tangled, as it can cause issues while printing. Once you get it set up properly, though, the results are definitely worth it. Overall, this is a gorgeous filament that produces stunning prints. It just takes a little extra attention during setup and use. I would recommend it to anyone looking to add a unique, colorful finish to their 3D printing projects!

Color is awesome! Prints great no tangles no clogs just consistent prints for the entire kilo

I’m a creature of habit, and it’s hard to pull me away from my Sunlu routine. However, Geeetech Dual-Color Silk really impressed me. It provides a level of visual depth that single-color filaments just can't match. If you want to take your decorative prints to the next level, this is a fantastic, reliable choice.

Fungerar utmärkt att köra som generic abs på Elegoo Centauri Carbon i 160% hastighet. Ger något blankare resultat än vissa andra varianter. Prisvärd produkt.

ＴＰＵ95Aフィラメントとしては他メーカーと比べて柔らかく、取り扱いに注意が必要です。 新品開封後にセットする際、フィラメントが柔らかく、チューブに通す際引っかかる感じがしました。また、 新品開封後、印刷するも糸引きが発生しましたが、十分に乾燥、ドライヤー8時間位行ってから、再度印刷を行うと、糸引きも無く綺麗に印刷が出来ました。 使用する前には、フィラメントチューブは短く、十分に乾燥させてから使用する事をお勧めいたします。

Pedido enviado con rapidez y bien embalado. Biene envasado al vacio como otros rollos de filamento de esta marca que ya he comprado con anterioridad. Trae una bolsa de plastico para poder guardar una vez abierto (Se agradece el detalle) El rollo es de 500gr y pesa lo que dice. Referente al material he tenido que ajustar algo los parámetros de ajuste de mi Ender 3s1 ya que al principio haciendo algun test me dejaba hilos, pero poniendo la distancia de retracción a 1,5 y la velocidad a 35mm/s, (Es extrusión directa) con una temperatura de extrusor de 215º y la cama a 60, la verdad es que la segunda prueba ha quedado de 10. Sin duda volveré a comprarlo. Pongo foto de la primera prueba y de la tercera.

Il materiale e buono e facile da stampare, colore brillante e bello da vedere

Compré 12 royos hasta el momento y probablemente compre más es un material que está muy bien y ya hice muchas impresiones con lo cual ningún tipo de problema! Viene bien enrollado y si se trabaja a una velocidad normal no crea ningún problema que no se pueda quitar después de la impresión.