Wireless Garage Door Opener Remote WiFi Switch Universal Controlled by Smartphone for Automatic Gate Opener System (Without Door Sensor)

I agree with a previous review. I was going to give 4 stars but price is great and functionality is excellent. Deserves 5 stars. Here's another lengthy review, but hopefully it will save you some time and frustration when you set it up in your garage.Overall, the LT3 device is very versatile. You can configure it to control 1 door or up to 3. I used it for my garage which has 2 doors. You have to be able to do a little bit of tinkering to set it up, but it isn't too difficult (especially when there are reviews like this). I have 2 Genie openers, but you can use this LT3 on almost any brand that has a standard 2-wire push button.Here are some highlights of my installation. I hope it helps you.1. I have 2 existing wall buttons, one for each door. The LT3 device can replace those, but it requires power, and it has a funky shape not too conducive to be placed into any standard electrical or switch box. I decided to leave my wall buttons alone and use the LT3 device purely for connecting to WiFi and for remote access via the phone. This saves some frustration in running power to the wall switches (and the unsightly power cable). I placed the LT3 on top of one of the garage door openers, and AC power is readily available where the opener plugs in. I know that I won't get to push the nice LT3 buttons, but I already have working wall buttons so it's no big loss. Also, my Genie wall switch has a separate button for the light and a lock switch. So it makes sense to leave those intact.2. You can use either AC or DC to power the LT3. I chose to use low voltage DC because the LT3 will essentially just sit on top of my opener motor, not in an electrical box. I don't want 110V AC running to it and then accidentally shocking myself. I found an old 12V DC power adapter for something I don't even remember, and just cut off the connector at the end and stripped the wires. Plug it in and use a volt meter to figure out which wire is positive and hook it to the RED LT3 wire. The other negative/ground wire goes onto the black LT3 wire (you'll also use the black LT3 wire for open/close detection). Secure the wires with small wire nuts or electrical tape. If you don't have a spare 12VDC adapter, you can buy one from Goodwill or used electronics store for cheap. Make sure you use a physically small power adapter. Since the outlet is on the ceiling, a bulky adapter could fall out of the socket from its own weight. If you want to use AC power, that's fine. Just find any old 2 prong extension cord and cut off the end, and strip the wires. The AC wires go into L/N sockets on the LT3. Know that the screws are unprotected, so it could be a shock hazard.3. You will want the Smart Life app. I already had it to control some smart plugs in the house. Once you have Smart Life set up and registered, you can press the "+" key to add a new device. Scroll down all the way and choose Other Products. It will then wait for a connection. Power up the LT3 and hold the Button C for 10 seconds until the wifi symbol blinks. You should now see the device on your Smart Life app. Once connected you can click to the 3 big buttons on the app screen, and the "gate open" status at the bottom. You can edit the name of each button (see my photo) as well as the LT3 itself. I called the LT3 "garage controller" and Button A is "big garage door" while Button B is "small garage door".4. Unplug the garage door opener while you are wiring. I used a spool of 20 gauge bell wire (twisted red/white solid copper) to do all my connections. It was about $10 for 100 ft. But you can use any low voltage wire that you have handy. Old telephone wire works too.5. Find where the wall button connects to the garage opener motor. For most openers, there are 2 wires coming from the wall button and goes into 2 contacts on the motor housing. Run 2 wires from the LT3's Com / A ports to these same 2 connections. If you want to control a second or third garage door, you will have to run 2 wires from Com / B (and Com / C) to the second and third garage doors. I ran these wires into the attic and down to the other opener, but you can also just staple it to the ceiling.6. Once you have the buttons wired, plug in the garage door openers to test. Mine worked pretty much on the first try. Make sure your wall buttons still work, your app buttons work, and any remotes in your car or homelink buttons in the cars still work. If you have a light button on the wall switch, make sure that still works too.7. I use Google home to connect to Smart Life. If you already had Smart Life connected to Google home, you will have to disconnect it and then reconnect in order for Google home to find the new garage door controller. To operate the doors, say "OK Google, turn ON big garage door", or whatever you named the button. Google Home at least at this time doesn't understand "open" or "close", but you can say "turn on" to toggle open and close. It is just like physically pressing the wall buttons.8. Now the dreaded (and desired) open/close status. First, you will need to buy a reed switch or magnetic sensor to detect open/closed status. These are 2 part switches, where one half has a reed switch sensor, and the other half is a magnet that triggers the sensor. They are used in home security systems to detect window open/close and they are very affordable. I bought 2 for $8. If your garage door opener already has limit switches (either mechanical contact or magnetic reed switches), they likely cannot also be used for the LT3. Save yourself some tinkering and just buy the additional reed switches. You will need one for each door you want to detect open/closed status. I chose to mount them on the rail and carriage of the opener (see pictures). Or you can mount them on the door and front wall. The sensor part is attached permanently to the rail and doesn't move. The magnet is attached to the carriage and moves. When they line up, the 2 wires marked Common and NC (normally closed) are shorted. You will want to use these contacts for the LT3's green and black wires.9. The LT3 can open and close 3 separate doors independently, but it has only 1 open/close status indicator. What I did to get around this limitation is to wire all the open/close reed switches in a series. I figured the only time I need to check the open/close status is when I am away from home. And in almost all cases, I just want to know that all garage doors are closed. Wiring the reed switches in a series ensures that the green / black wires are shorted (and app says "gate closed") only if ALL doors are closed. App will say "gate open" if ANY door is open. You will have to figure out which one is open by pressing a combination of the buttons. For most of you, you will use one door more often than the others, so it won't be hard. With 2 doors, it only takes a maximum of 3 tries to make sure both are closed remotely. With 3 doors, it's a maximum of 7 combinations. Not ideal, but since there is only 1 open/close status indicator, this is the only way to do it. It is still better than not knowing whether you left any of the garage doors open.Hope this helps someone. See attached wiring diagrams and pictures.Cheers.

This does exactly what I needed, which is open my garage doors from my iPhone. I don't like that you have to sign into a service, but it seems that's where the world is headed as there aren't other options. It only has open sensors for one door which is odd, given that it's an opener for three, but that's what you get when... well I'll refrain from the old man speak. If you want that I recommend you look elsewhere or get another solution, but really you can wire it in series and get the same result.Revising this to 1 star. This has stopped staying connected to my network, and without the stuff I don't need it basically doesn't work. Bummer, but typical given the source.

This device was relatively easy to install. I’m not sure why there is no wiring diagram. That would help a lot! The A and Com connections should be connected in parellel to the button wiresA couple of notes:1. You can use AC power- you have to supply your own cord or hardware the device to AC power. AC wiring connects via the screw terminals.ORYou can use DC power connecting to the black and red wires coming out of the device.2. This is a crazy form factor. I don’t know what they could have possibly been thinking when they designed this thing! It’s like a half height outlet box size.3. Although my device works perfectly, every time I start the app, it wants to do a firmware upgrade. The firmware upgrade always fails, I never get it to work. If you accidentally consent to the firmware upgrade, the app is worthless for a couple minutes. This hasn’t happened yet, but I know someday I’ll be stuck in the driveway waiting for the darn thing to time out and fail trying to update.The app is pretty simple. You can label the buttons which is nice, but not the open/closed status light. So my button says Garage Door, but the status light says “Gate is closed”. Also it would be nice to be able to select the number of buttons the app shows between 1 and 3 Showing unused buttons is unnecessarily confusing.I really do like the unit and I’d happily buy another one. The only other device out there that lets you see open/close status is more than twice the price at $99.

This switch is more than I expected. I understood this product thoroughly after read all details on the product page, it’s not so complicated as I thought before, you can take it as a traditional wall push button which has WIFI remote control function. As I have unused remote controls for my yard auto gate, a bold idea came to my mind, I can connect the switch to my remote control! 1, I test my new remote control at room to see whether it can open my yard gate (put the remote control within its normal working distance is important), fortunately, it works. Then I began to do the modification.My remote control has 3 buttons which function as open, close and stop, and this switch also has 3 buttons, it’s perfect. I opened up the remote and found that there are 4 terminals for each button, what need to do next is to use a multimeter to find out the Com terminals, it’s easy if you know a little about electronics. 2，Pick one of Com terminals to solder wire to the WIFI switch Com terminal. And pick one of the remaining terminals for each button to solder wires the WIFI switch A, B and C terminals. 3，Assemble the remote control and test whether it can continue to work, make sure that I didn’t broken it during soldering. Because this kind of connection is to make sure the WIFI switch to work the same way as the remote. ,4，Find a power cable with plug, connect the power cable two wires to the WIFI switch L and N terminals. This step is easy.,5，Next, I power on the WIFI switch to test whether it can work the same as the remote, and it just worked as I expected!,6，But it’s not over yet, I need to pair the WIFI switch to mobile APP, I followed the manual to download, register and add the WIFI switch to mobile APP, it’s much easier than wiring. After all finished, I can control my gate by mobile at last.This switch is really an awesome product, I don’t need to worry about buying new remotes, losing them anymore, and I can share it with my families, they don’t need to take remote either.

Is it a 3 or is it a 4 star product?Positives:Hooked up to Wi-Fi easily.Works as advertised.Cost (sort of positive)Cons:1. Software is fairly rudimentary, but does work. See other reviews on what is lacking in software.2. Instructions. There really aren't any with the product but other reviews give sufficient detail to ultimately figure it out.3. Hardware not delivered complete.If you want to install as suggested with DC connections you must obtain a transformer. I actually had one in my goodwill donation box, I snipped off the plug and matched the solid black wire from transformer to the black and the other transformer wire to the red. I actually had little wire nuts and some 18 Guage wire in the garage! Woohoo! This was for connecting to the operators wall panel.Also there is no receptacle for the unit to mount it anywhere so, it's just hanging by the wires right now. Not ideal.The actual installation time is less than 30 minutes if you have everything handy that you need, if not you can spend a morning locating the additional items needed. If you need to purchase the additional items I'm not certain the cost is going to be so much lower than some of the other more "polished" products available.So while I'm not finished installing (it's not mounted) I still decided to give it a 4 star rating as it is accomplishing its purpose. I have a 20 year old craftsman / Chamberlain door operator which it's working nicely. I'm going to try to figure out how to connect it with my Skeeter Beater garage screen which opens with a tubular motor. (I live in Florida) if that occurs I will update my review with the information.

Using a 2003 (?) Liftmaster garage door with garage door button, light, and lock. Also Using normal AC Home Power to power device. I only cared and tried to get the device to open and close the garage. I didn't care if this device could Lock or Turn the light on/off.Sorry if it's long, I'm trying to help anyone decide if this is also right for them. This is a WiFi connection, not bluetooth or Z-Wave. I will come back and try to answer questions too. I am not going to proofread this more than 2-3x as it is so long lol. I may have duplicate info but the more the better. I was easily able to add control functions to my family members by just adding the "Wifi APP and SMart life to their phones and linking the Smart Life app to their google home using my login info. This is my family so I trust them. :) I did not have to go through extra steps to authorize someone, but that is probably easy too.I was able to get this working per lolsmurf's notes/comments and the videos posted by the seller on youtube. Just google He Jue youtube and you will find them. At this time of posting they had 3 videos. Their videos only helped me connect the device to my wifi. Which was to hold down gate 3 button (top) for around 10 seconds then the wifi would try to connect, then with their APP "Wifi Smart Control" I was able to connect it to my wifi (typed password) and test the buttons. You can do this with just power, and not have the garage door opener connected. After I connected my 2 wire power cord I bought, I did this in my kitchen closest to my wireless router. The thinner cord I wanted I could not find, so I bought a slightly thicker round cord that worked just fine. the thinner one may have got the job looking cleaner looking, but I couldn't find it. what I had worked fine and powered up. I then added it to my "Smart life" app I already had on my phone. I basically had to do the same thing, hold gate 3 button until wifi light on the device went out and told the Smart Life app to discover. It found it and I named it garage accordingly. I named the whole device garage room and the next thing in the list for me I named just garage. This allowed me to add it into google home and say "ok google, turn garage on" and it opened. I already had several devices in my Smart Life app, so I had to "unlink" Smart Life from google home app, then link Smart life again and all my devices appeared. I already knew of this bug when adding before so it was easy to fix. For mounting I was going to drill a hole to use the "what looks like" mounting holes, but I could not easily snap it apart, so I just used heavy duty velcro and mounted it right beside my current switch, which conveniently had notches on the side that I fed the wires through too. I really wanted it flush in or attached with a screw. But this should be fine since it's not really in the elements of rain/snow.Here are the things you will need to do if you don't have dc power available. I didn't have dc power so I could not use the wires already there. I did not care if the app said "door open", for this to display right it is a separate sensor and I will have a camera looking anyways so I can see if it's open. I only cared if I could open and close the door from my phone and google home.(Below is using normal AC home power and a liftmaster garage door - NOT using the attached red/green/black wires at all)1a. Buy/locate a 2 wire AC appliance cord from your closest hardware store (one end with 2 prong plug other with wires. I used home depot, but lowes also has it for about $8..amazon also has it.)1b. Connect this AC wire to the device. Connected In this fashion to the device. Black wire to "L" on the device, and White wire to "N" on the device. The device should power on when plugged in if you did it right.2a. Buy/Find low voltage wires to open/close garage door to connect to this device. (I bought 5 ft of red/white bell wire for $1.20 from Home Depot - I connected it directly to my current switch...so if I ever move or if one switch breaks, I can use the other)2.b Remove current liftmaster white cover, remove the 1 screw, then push up on the liftmaster control panel. This will take the panel off the wall and you will see the wires that goto the motor. This will expose the Red (R) and White (W) connections you need seen in my pics. Connect red to red and white to white on the original control switch. Then on the new device Red wire goes to "A" and White wire goes to "COM". All seen in my pics. You can do B or C, but A just specifies that "Button A" will be the one you use...it's top button in 3 button app. You can rename as you want in the app and in smart life and google too.3. Put everything back together and test.

The directions are terrible even for those mechanically inclined like myself. I had to figure it out. The app and connecting the device is more of a headache than the installation. After several hours I finally got it connected. Then all of a sudden it disappeared as a known device from my app. I tried to reinstall it and I was finally able to get the app to see the device again but it would never go all the way through the process of adding it as a known device. It is Chinese made junk which is evident by the spelling and grammar in the directions. Don't waste your time on this and just buy the name brand that fits your garage door. If I've helped one person to avoid this absolute headache then I've accomplished my mission. Terrible product.

Update: We have had this unit for 10 months and update the rating to a 3 stars. It still works, and the issue with the remotes is intermittent, and the light in one of the touch buttons is starting to dim.... but it still serves its intended purpose.....i would recommend to friends with a warning of its lacking features.....Original review 2/2019Gave it 2 stars for the following reasons....The item works as how its designed, instructions are useless....you have to have a above average understanding of electronics to be able to use this, once installed.....say goodbye to all your garage door openers because they WILL NOT WORK anymore....i have one built-in in my SUV and I have a keypad remote, and a couple of other basic clickers in other vehicles....NONE of them work anymore the only opener that works is the one that is wired...it only works on the app if you want to open remotely....the bad part is, if someone opens the garage door manually or if the garage door is opened accidentally with the wired button...IT DOES NOT HAVE ANY NOTIFICATIONS THAT THE DOOR IS OPENING....i had to install a camera so that i can see if the door is opening accidentally.....i would have returned it if i found out before i created a hole where i mounted the unit....now cosmetically i have to leave it there so i do not have a hole on the wodden panel.....if you want to giveup all your wireless clickers and remote, then this is for you. But if you intend to have other remotes, i would avoid this....oh! If wifi is down or weak for obvious reasons the thing does not work....