Space Pi Filament Dryer Plus, 2 Spool 3D Filament Storage Box | 360° Fast Heating Dry Box with LCD Screen, One-Key Drying for PLA PETG ABS TPU PC PP ASA PET PETG-CF

It does it's job, and it does it well. Overall, I am happy with my purchase.I have a roll of clear TPU I had sitting in a non-air-tight bag for about 6 years in the basement and decided to see how bad moisture impacted it. (It was really bad, as can be seen in one of my pictures.) Threw it in the drier with the recommended settings and got impressive results; it dried out the filament and made it printable again.I also recently purchased a spool of Elegoo rapid PETG to try out the brand and was disappointed with its performance out of the box as it was laden with moisture. I would have been annoyed and writing an email to support because I had an unusable spool of filament, but this drier came in to save the day. Now I'm just annoyed, but at least I have a usable spool of filament.Having saved two spools and used this to guarantee an additional two spools in my collection were good to work with before large prints, I can say my investment has already paid off.(Included in my review are also thermal images of the drier running; it's pretty interesting to see the channel the hot air is blown through by the fans and how it heats the spools.)I am however disappointed with the quality of the touchscreen; it feels very cheap, has visual artifacts when pressing on it, and mine arrived cracked. (You can see some hairline cracks light up in the display itself when pressing on the screen to use the interface and they go away after a few seconds.) The screen is still fully functional, just looks bad when you need to touch it.

Excellent product. Works great and is easy to use.

With the humidity in my area steady at about 60% all year, this thing really helps me dry my filament out. I would totally recommend this to folks looking to try out filament.

I appreciate the two spool capacity and ease of use. I can quickly drop in a couple rolls, set it and leave it to run without issue. However the case configuration is a bit weird to me. I want to have the screen up front, but I need a lot of empty space behind it to give the cover enough room to swing open, so it requires a much larger footprint than you'd expect. It took me awhile to figure out a good place for it on my table with the 3D printer.Also, the touch screen feels fragile, cheap, and not very responsive. It flexes a lot when pressing on it, and the lit up numbers fade in and out if you press hard (which you need to). I'm used to it after using it awhile, but I don't love it.

I used to just run filament and normally it was fine. Then I pulled out some older spools of PLA that had been sitting for years. If you looked at it funny, it would snap.I read up and realized that was a symptom of 'wet' filament.Bought this device and dried the wordt two rolls for 12 hours and they ran through my Ender 3 V3 SE like a champ. Now any roll that's spent time laying around gets 8-12hrs in the drier with a dessicant packet in the hub getting dried out and then used and sttraight into a 1 gallon ziplock for storage.This drier is easy to use, can do two rolls at once and has given me great results.

Terrible customer support!Right out of the box, this device hasn’t worked. Turn the power on and the touchscreen power button comes on, but doesn’t respond to touch. Never used the device one time.I have been fighting with the company since receiving this item in January. They refuse to send me a new device and have sent out a new screen, that they want me to replace. It’s been in the mail for months now and they have stopped responding to my emails. Amazon won’t assist because it is now past my 90 days.I get that things break, but I’ve paid $90 for a brick and can’t seem to get help from anyone. Not ok, Creality!

Works well but display has been dropping characters after only a month.

Tried another unit but it wouldn't get hot enough. This unit hit target temp or slightly higher in multiple parts of the chamber. Only bad is bottom gets so hot it damaged the wood table I was using (split the glue line between boards). So, I recommend for PETG, ASA, etc. but make sure to put a hot pad of some kind under it.

フィラメントがしけると、仕上がりに影響があるとのことなので念のために買いました。なんとなく、失敗が減った気がします。

Tengo unos 5 años de experiencia en la impresión 3D y noté que en los últimos meses medio mundo recomienda secar tus filamentos para mejorar drásticamente la calidad de las impresiones, así que decidí probar con este producto de Creality, cabe destacar que siempre he mantenido mis rollos en bolsas ziploc y con sus respectivas bolsas de desecante, esto no cambiará.El secador funciona bien, no tuve problemas de mal funcionamiento como otros comentan pero lo único que no me gustó es tener que usar tubos bowden para meter el filamento en ellos y después en tu impresora, uso impresoras de extrusión directa y esto claramente afectará a las configuraciones de retracciones, también noté que el extrusor necesita hacer más fuerza para jalar el filamento, hay más resistencia a causa de los tubos y esto no me gustó, no quise forzar el motor del extrusor y al final solo seco los filamentos, los saco del secador y los coloco en el portarrollos de mis impresoras como siempre lo hice.Se nota la diferencia en la impresión, también se nota en los rollos, estos hacen un ruido peculiar al manipularlos, como rechinidos, el material al estar seco rechina cuando tiene fricción entre si, creo que esa es la señal de que ya están listos para usarse.Otra cosa que noté, cuando abres la tapa del secador, al instante baja algunos grados el porcentaje de humedad en la pantalla, como si estuviera acumulada en el interior y al abrirla "liberas" algo de esa humedad. Puse sin preocuparme un rollo de PLA y otro de PETG con temperatura de este último, veo que al usar 60 grados la humedad baja más rápido, pero pienso que es un error del sensor, parece ser que a 60 grados si indica la humedad correcta y 50 tiene menos precisión. Si tienes un PLA un buen rato con sus 50 grados y notas que no cambia el porcentaje, prueba subirle a 60 (cambiar a PETG) por unos minutos y verás como baja más rápido, no sé que daño se pueda causar al filamento si es que lo causa, pero yo dejé un PLA por horas junto con un PETG, después imprimí sin ningún problema con ambos.

I did a lot of research before I purchased this. While I never buy the most expensive thing... I never buy the cheapest thing either. This filament dryer seemed to be in the middle when cost was concerned, and being able to dry two spools at a time (and even print with them, if I wasn't using my AMS) is a real plus.Never had an issue with it (although it doesn't seem to have a place to vent out the humid air)Anyways, I'm happy with the purchase. No complaints.

La recomiendo, hace todo lo que describe e incluye 2 tubos blancos para imprimir mientras se seca, la estructura, y su funcionamiento por aire la hacen efectiva, en general tiene buenos materiales de construcción aunque al abrir y cerrar la tapa rechina, pero con un buen manejo no es un problema. El ventilador es bastante silencioso para ser un 5015 aunque hay gente que dice que es ruidoso, definitivamente mucho menos ruido que una impresora mientras sólo se calienta.Sólo tiene un pequeño "Problema", fácil de resolver. La estructura del SpacePi no tiene ningún mecanismo de sujeción como los conectores neumáticos para los tubos. Por lo tanto si imprimes mientras está secando el filamento, el tubo se estará moviendo hacia adentro de la secadora ocasionando atascos, rotura de filamento o algún daño a los equipos. Pero en Printables hay modelos para imprimir soportes para los conectores neumáticos, una vez instalados ya no hay ningún problema para imprimir.

Great machine in the beginning, really helped print quality, however, after about 9 to 12 hrs of use fans started making a grinding ( or off balance noise) it was random some times you would start it made the noise then start it again and it was fine then would make noise after starting had to return to bad really like the machine.Update..Ordered a second one and machine is working great love able to have a roll in the machine and printing from it while another can just be drying out for use.