4 Pack Hall-Effect Joysticks Replacement for DualSense PS5 Controller, 3D Analog Sensor Wheel Thumb Sticks Joystick Rocker Module Replacement for PlayStation 5 Controller

I bought these hall effect joysticks to permanently fix the drift issues that started showing up on my PS5 dual sense controller. I am very happy with how they perform now that the original joysticks have been replaced with these hall effect sticks and the controller has been recalibrated. But a word of warning- this is not a simple or easy fix. If you do not have experience or the equipment to do solder rework you will most likely have a very hard time replacing these sticks without damaging the controller. I would consider a hot air rework station imperative for this operation as the solder is that horrible RoHS stuff that only melts at temperatures approaching the surface of the sun. If you do not have the equipment or experience I would recommend the much easier fix of simply swapping the wiper guts on the existing joystick potentiometers. It is a much easier task and will get rid of drift for another couple hundred hours. After either fix you will also need to recalibrate the controller with 3rd party diagnostics run off of a computer.If you have the tools and the knowhow I would definitely recommend buying these replacement joysticks to permanently fix your PS5 controller drift issues.

works ok, makes it a little more touchy though so you might want to lower your sensitivity after

Good quality all around. The parts and the tools. Installation was a breeze. Follow a YouTube video step by step and saved myself a bunch of money!

the sticks worked at first but now it has started drifting after one week. low quality product that is breaking down fast.

these sticks are decent for what they are but they have over range issue giving me an error rate of 10% and this cannot be calibrated out they include these shaft wraps and u need to use 2 on each stick to get the circularity to be even and get the error rate down to 5% but that ruins the feel and make them feel sticky i would not recommend these are definitely the ginful v5's stick more like v1'sthe 8% is with the wraps and the other is without

Just finished replacing all 4 joysticks on both of my controllers and right out of the gate, they work great. I highly suggest plugging your controller into your laptop and calibrating it at https://dualshock-tools.github.io to ensure you have it centered properly (very easy process).If you dont have a soldering workstation, you will need to make sure you get the essentials before attempting this replacement. It takes a moderate amount of dexterity and know-how when it comes to removing the old joysticks, desoldering, and soldering in the new components. I wish I had a desoldering gun for removing the old joysticks because using a focused heat tool and desoldering wick was a biznatch.At minimum get yourself a desoldering gun, a soldering iron, solder, and flux before you get started. Doesn't hurt to have some 90% or higher alcohol available to clean the circuit board if needed.Great product thus far, hope it holds up and myvcontroller drift stays a thing of the past.

Work as expected for a PS5 controller that was previously experiencing drift. 3 of the 4 would have been fine with no calibration, but one was drifting slightly in game play. Went online and calibrated them on DualShock/tools.github.io. A few other reviews had mentioned issues with their R3. In my case, no issues with my L3 or R3, they still work fine.Removing the existing hardware is a pain, in part due to the number of pins involved and the fact lead free solder requires a higher temperature. After spending too much time trying to desolder ~14 pins and remove as a whole assembly, I ended up breaking it down into smaller parts. For example, disconnected a pot and removed just those 3 pins. Much easier doing it in small steps. Once I got the hang of that trick, the second (left) one took half as much time as the first (right).A nice small flush snippers, desolder braid, and flux are the accessories you need - in addition to a soldering iron and solder. If you don’t know what those are, then this project probably isn’t the one for you.

Amazing solution to fix stick drift on the PS5 controller. Knocked one star off as one of the joystick had a different "click" and feel to it when pressing down on it. I only realized this after going through the whole process of installing it. So now I am just going to live with it