BIQU CryoGrip Pro Frostbite for Bambu-Lab P1S/P1P/P2S/X1C/X1E/X2D/A1 257x257mm Cold Build Plate Room Temperature Print Double Sided Upgrade Plate Removable Surface Platform

Just a gentle reminder. Please wash the plate with soap and water then perform a calibration or re measure the z offset.Using on a H2S. The plate works great at 42C. Sticking is good without being obnoxious. Have used it for 6 prints with lots of small/large supports and it’s been really good. It’s a great value considering you won’t need any adhesives and you actually save a tiny bit on electric with the lower bed temps. It fit perfectly on a Bambu H2S but had to disable the bed checker which caused no issues. Zero issues with bed adhesion on first layers. The only question is how long will it last?

I run a small 3D-printing farm, and this build plate impressed me immediately. I had a part with large overhangs that kept tipping over on other PEI plates, even when using a brim and glue. On this plate, the same part printed perfectly on the first attempt.There is a little bit of a learning curve because you need to research and adjust the correct plate and temperature settings, but the adhesion has been excellent once configured properly. For difficult models, tall prints, or parts with limited contact area, it has been much more reliable than the standard plates I was using.I was happy enough with the results that I purchased these for my other nine printers. I am still waiting for a sale before buying the more expensive version for my H2C, but so far these have been well worth the investment and a great addition to my print farm.

Got this for special material, worked great, fit my x2d. easy to use. great adhesive keeps print on plate. no mess

I bought this build plate for my Bambu Lab H2S and it has been performing flawlessly. I regularly print tall, multi-hour parts, and this plate gives me the confidence that everything will stay perfectly adhered from start to finish.Adhesion and reliability:Layer adhesion is excellent right out of the box with no extra glue or spray needed. Even with tall or narrow prints, I haven’t had a single corner lift or part detach mid-print. It handles repeated heating and cooling cycles very well too.Surface quality:When I first unboxed it, the packaging left some bubble wrap marks on the print surface. They didn’t come off even after cleaning, which made me worry at first. Thankfully, after a few prints, the marks naturally faded away and the surface now looks and performs great.Fit and compatibility:Fits the H2S perfectly and the magnetic base has a nice, even pull across the bed with no hotspots or shifting.Overall:A well-made, reliable plate that provides consistent first layers and peace of mind for longer prints. The packaging could be improved, but performance has been excellent. I highly recommend it for anyone using a Bambu H2S or similar setup.

Love this CryoGrip Pro plate! It gives excellent adhesion for PLA and PETG at noticeably lower bed temps (around 45-55°C for PLA) than my stock textured PEI, which helps reduce warping on bigger prints and saves a bit on power. The subtle fine texture looks almost smooth but grips reliably without needing glue for most filaments. Prints release easily once the bed cools, and the pink color is a nice touch. Durable so far after dozens of prints — highly recommend as a versatile upgrade, especially if you print a mix of materials.

Hello,I am very disappointed with my CryoGrip Pro Frostbite plate. I used it on a Creality K2 Plus under normal operating conditions, and after less than two weeks of use, the coating on one side started to lift and peel off.I purchased this plate through Amazon in the United States and brought it to my country, Guatemala. Because of the distance and the shipping and import costs involved, returning or replacing it is not easy, which makes this situation even more disappointing.I have previously purchased the blue plates from the same brand and had excellent results with them, so I expected the same level of quality and durability from the Frostbite version. My positive experience with those plates was the reason I decided to buy this product.In my opinion, a coating should not deteriorate like this after such a short period of normal use. I would like to know whether this could be considered a manufacturing defect and if there is any way the manufacturer or seller could assist me.Thank you.

Was on the fence after reading other reviews but decided to get o e for my P1S. Probably the best accessory I have bought for it and it is now my go-to plate, replacing my OEM plate. No issues with adhesion, plate seems quality material. I have even personally not cleaned it, touched it to “stress test it” after multiple prints, still “sticky” and worked like new. Would recommend ordering buy again if I needed to.

I earlier purchased the Cryogrip Glacier plate because I use PLA/PETG/ASA frequently. After trying it, I decided I needed more sticking power for my PETG filament than the Glacier offered. So I decided to try this Frostbite version for my PETG/PLA and reserve the Glacier to my ASA filament prints..The Frostbite is very comparible to the Bambu Lab Supertak Plate and I use those Bambu Plate settings with this plate too since Bambu doesn't allow custom brand plate settings on the P2S so far. The Bambu plate settings you choose to use this plate with do make a difference. Each Bambu plate setting type will change the printing Z heightby small amounts and it will make a difference. For me, choosing the Bambu Supertak plate settings has been the best fit.The Frostbite grabs onto PLA and PETG FAR better than any of the other brands of plates I've tried, including Bambu's plates. That's what I wanted above all else... Lot's of stickability.As a side beneift I can also print the same PLA/PETG filaments at lower temperatures that save energy and still stick.Now the downside to this is that this plate is only a tacky cool plate that can not run much of anything other than PLA/PETG. And it absolutely can not be set to higher temps or the surface of it is ruined.Also you absolutely should not clean the surface with alcohol or harsh chemicals at all. Soap (with little to no residue, like Dawn dishwashing detergeant) and water only. Use a sponge or microfiber cloth under the water to avoid scratching it. Don't use a brush. Alcohol will definately damage the surface.Also do not scratch up the surface of this plate by using a sharp edge to remove parts from it. You must wait till the plate has cooled a bit to release the parts easily. If you pry off a part from the plate especially when still hot, you will damage the surface of the plate. Be patient and wait for a cooldown time before removing the parts from the plate. So wear and tear on these Frostbite plates are more of a concern if you are not careful in their use.Also in time, the surface coating will wear way and the plate will need replacing as it just won't stick or release like it used to. Some people report this happening in mere months and others say they have put a thousand hours on them without issue. I haven't had mine long enough to make a judgment now.I do like this Frostbite build plate much better than the Glacier or the Bambu Textured PEI for PLA/PETG filaments. It's also a different texture than those other plates. So sometimes I will choose which one I use by the texture I want or don't want on the bottom of the print. But for my high temp engineering filaments the Frostbite is useless. The filament type restrictions and required careful use and cleaning warranted a single star rating reduction.Overall a great build plate for PLA/PETG only if you use a bit of care in it's use and cleaning.

entrega rápida e perfeita.

本アイテムは、オールマイティなフィラメントに対応ものではありませんが普段使いのフィラメントに特化したアイテムです。安定した定着性と低いベット温度で省電力を両立している良アイテムです！

With this build plate I can print PLA at 30°C bed temperature. This let me reduce the power draw of the printer so that I am able to run this printer on a 1100VA computer UPS without any issue.Edit: this was possible because where I live the room temperature is above 28.

Works really well, just as advertised. I would recommend printing with bed temperatures at the lower end of the recommended temperatures and wait until the plate cools down before trying to remove the print

Nao faz milagre