Klipsch R-610F Floorstanding Home Speaker, Pair

Easily handles the new power amp I bought. Imaging is very good as well.

When these Klipsch R-610F tower speakers went on sale for $300 a pair, it was really a no-brainer to pick up a pair right away. We are running these Klipsch R-610F speakers as rear surround sound speakers in our home theater (powered by a Denon AVR-S760H AV receiver). These Klipsch R-610F speakers are definitely an upgrade over the Klipsch R-41M bookshelf speakers that we had previously been using as rear surround sound speakers. Although, the Klipsch R-41Ms are now functioning very well (amplified) on my desktop computer, along with an 8 inch subwoofer. The Klipsch R-41Ms are definitely a huge sound quality improvement over the Edifier 2.1 speaker system that I previously had on my computer. We have these Klipsch R-610F speakers elevated on 6.5 inch tall speaker stands (actually heavy duty black foot stools) in order to get a little more height out of them for the rear surround sound movie effects, and also for multi-channel stereo music. Oh what a difference a little extra tweeter height makes in presence and clarity for the surround sound speakers. The sound output hardware of our home theater now consists of a Denon AVR-S760H AV receiver powering two Klipsch R-625FA (with Dolby Atmos height speakers integrated) front tower speakers, two Klipsch R-610F tower speakers used as rear surrounds, a Klipsch R-52C center channel speaker, and a Klipsch R-120SW subwoofer. This Klipsch line of reference speakers really sound amazing for the price, when both watching movies and listening to music. These Klipsch R-610F speakers will actually play some really low frequencies (rated at 45hz) for only having one 6.5 inch woofer. The Audyssey speaker calibration software in the Denon AVR-S760H receiver actually sets the crossover frequency for these Klipsch R-610F speakers at 40hz. However, we run these Klipsch R-610F speakers at 60hz, in order to give them some low-end breathing room, and send most of the lower frequencies to the Klipsch R-120SW subwoofer. The THX crossover standard is 80hz, but these Klipsch R-610F speakers do play very well down to 60hz plus, while using the subwoofer to pick up the lower frequencies, especially when listening to music in multi-channel stereo or Dolby Atmos modes. These Klipsch R-610F speakers are also fairly sensitive, rated at 94db, so they will play loud with very little amplifier power. The crossovers are set at 1,800hz, so most of the higher mid-range instruments and voices go to the tweeters. These Klipsch R-610F speakers are rated at 85 watts RMS, and 340 watts peak power input. However, I would take that 340 watt peak power with a grain of salt, as it can only be handled for milliseconds at a time. However, as stated previously, these Klipsch R-610F speakers will play LOUD with very little amplifier power. Of course, thanks to the one inch aluminum tweeters and the patented Tractrix horns, these Klipsch R-610F speakers also have that distinctive "Klipsch" treble sound that people either love or hate. I personally like the sound a lot, but for those people that wish to tone down the treble it can easily be accomplished in the high frequency (treble) tone adjustment or EQ settings of any good quality receiver/amplifier. These Klipsch R-610F speakers shipped from Adorama (through Amazon) in 3 days. The speakers were both delivered on the same day, and in perfect condition. These speakers come very well packed and protected, so be prepared to dispose of lots of cardboard and Styrofoam. These Klipsch R-610F speakers are very well built, and they are also fairly heavy and large at 36 pounds each. The speaker dimensions are 37 inches tall, 9.4 inches wide, and 15.1 inches deep (counting the width and length of the attached feet). The speaker cabinets are MDF covered with nice looking black wood-grain vinyl. The cabinets are reinforced internally and they do not resonate at all when playing low frequencies. The back of the cabinets have a huge Tractrix tuned port, and 5 way speaker wire binding posts (at the cabinet bottom), so banana plugs can be used. The banana plug holes are covered with plastic protective caps that take some effort to remove. I use FosPower banana plugs and 14 gauge OFC speaker wire with these speakers, and they both work well and sound great. The one Caveat that these Klipsch R-610F speakers have, just like all of the Klipsch Reference series tower speakers, are the 4 really cheap screws that are included with each speaker to be used to attach the plastic legs with. I suggest either drilling the predrilled holes a little deeper before installing the legs, or use some good quality, course threaded, self-tapping wood screws instead. I usually use my own good quality wood screws on the Klipsch Reference series tower speaker legs, and I have never had any problems when attaching the legs. Overall, these Klipsch R-610F tower speakers are really nice sounding and looking. The copper coated woofers and driver fasteners, along with the large Tractrix tweeter horns, make the Klipsch Reference series of speakers look very unique, to-say-the-least. Even though Klipsch Reference series speakers come with really nice magnetically attached black cloth grills (except the subwoofers, which attach with vibration-proof metal grill studs), I always keep the speakers uncovered because they look so cool. Heck, even the wife approves of the "cool" look with the speaker grills off (Yay!). The fact that the wife likes these speakers, as well as the great sound, quality, and look of these Klipsch R-610F (and all other) Klipsch speakers makes buying these speakers a real joy, especially at this great price level. Pick up a pair of these really nice speakers now, while they are still available!

Just purchased. Really excellent sound for the money, even without a sub-woofer.

Perfect entry level speakers. Beat the soundbar, but one gotta have a center speaker too.

Klipsch Reference R-610 Speakers sound awesome with or without a subwoofer.