Front Load Washer Tub Bearings and Seal Kit Fit for LG & Kenmore Etc Replacement Part 4036ER2004A 4280FR4048L 4280FR4048E 4036ER4001B

Bought this assuming the noise from my washer was caused by the tub bearings. Once I had the washer apart, it was very obvious that the bearings were showing their age and feeling crunchy. This repair kit installed easily in an evening after work, and there is also a good YouTube video on how to perform the repair! My LG TROMM washer works perfectly now and is quiet again! Would 10/10 recommend this to anyone else. Money well spent!

After checking on the replacement cost for my washer and dryer, I decided to give replacing the bearings a go even if it was clearly a daunting task. Taking out the old bearings was a bear since it was rusted, split in two and seemed like welded onto the drum and the shaft. With the help of Dremel I was able to carefully take out the old bearings and these fit perfectly. My washer now works perfectly and will probably last another 10 years.

The media could not be loaded. Update #2 11/17/2020 - This item is complete garbage. "THESE" bearing lasted 2 months before starting to degrade, so again I replaced them with OEM LG bearings. 7 Months with a Genuine LG Bearing still sounds silent like a new washer. My advice stick with OEM. This is a monster job, you don't want to do it twice like I had to.Update 4/2/2020 GARBAGE!!!! I'm giving a generous 2 Stars, because after 2 months these bearings started to fail, sounding like before I replaced them. Now at 6 months these bearing are in total failure, louder than the 10 YEAR old ones on the OEM (listen to the video, these are the new bearings after 6 months). Just ordered LG bearings. I will wait 2 months and post another review to rule out any other part causing the failure. If the LG ones work I'm dropping to 1 star.First this is a monster undertaking will take a full day, but the end result is a super quiet washer again. Tips: 1. Buy a new front door gasket, shocks and lg spring expansion tool, you take off these items anyway. The spring expansion too is the best 25 dollars you will spend. Took me 30 minutes for 1 gasket spring installation, cuts on my hand and bruises on my knuckles without the tool 2. YouTube video for installation and use ziplock bags to label, keep track of screws, 3. Use a sledge hammer, hit drive shaft directly square on top, it will easily separate it from bearing without damage. I used a mallet, sledge with a piece off wood, shaft didnt budge even hitting it hard as I could. Hit shaft once with a sledge hammer directly, with 1/2 the force worked like a charm. 4. Use a thin film of laundry or hand soap on bearings and door gasket spring grooves. Will make installation much easier. 5. Remove the bars on inside of drum, only takes 2 screws. Mine were caked with soap scum underneath. If you ever got that grey slime on clothes this is why. Clean all soap scum out of tubs and stainless drum too. Good luck

This part arrived on time and was all intact. Unfortunately, it wasn’t until trying to install the bearing that I found out that the washing machine tub/ spider arm also needed to be replaced. it was cheaper for me to just buy a new washing machine. I looked into returning the product but it was already past the time frame for doing so. Currently I have the parts listed on offer up for sale. The only reason I put three stars in the easy to install and noise level was only due to the fact that I did not follow through with the installation. But honestly the price was right and the parts were in good condition so I would order again from here. also, I would recommend to a friend or to anyone reading this review to order from here if they have the parts you need.

Installed these TWICE in my LG Tromm front-loader that sounded like a jet engine on the spin cycle. The first set didn't last more than about 3 months. I believe I messed them up on installation. Using a hammer (even if careful) to install these may mean you've shortened the life of them in a massive way. After 3 months they were noisy again and inspection showed them to be completely disintegrated and had leaked all of their grease. They had tons of play and were worse than the originals.The SECOND time I'm more confident that they'll last. I used a bearing pusher / puller to install properly, which makes the job 100x easier and pushes them in with no risk of damage. Now my machine is as quiet as when it was new.Note: it's best to buy a new drum spider when replacing these and you'll need to apply a small amount of grease on the seal washer in order to avoid squealing where the rubber meets the metal shaft.I'll update this review if the new set deteriotes like the first, however I'm pretty confident it was my 'heavy handed' first installation that set the first set up for failure.Edit: 4 months later and we’re still golden. Will update after more months have passed.Edit: 13 months in... still good.Edit: 16 months and counting. A-ok.(Hint: bearing pusher is the key to a successful installation)