XiKe 4036ER2004A, 4036ER4001B, 4280FR4048E and 4280FR4048L Front Load Washer Tub Bearing ＆ Seal Kit Rotate Quiet and Durable, Replacement for LG and Kenmore Etc.

First and foremost, installing these bearings is not a quick or an easy task. It was hard work with unforeseen issues. In the end it was worth the effort because the washer is now operating like new.And now the review. I'm writing this review about two months after installation. This bearing/seal/o ring kit worked perfectly. I'm extremely happy with the purchase. But the install process wasn't easy. This is not the fault of the bearings. It was due to the age and condition of the washer. And the method I used to remove one of the bearings that was galled onto the drive shaft.And now some background on the repair. This may help you decide whether to attempt this repair yourself.My LG WM2301HW washer is 10+ years old. I've had to perform several repairs on it over the years including:- replacing the drain pump.- replacing the shock dampeners.- replacing the rotor (part of the direct drive motor).So I'm not afraid of taking the washer apart. It's a well designed machine that isn't difficult to repair if you have tools, mechanical knowledge and you watch a few youtube videos. This washer repair was the most complex one I've performed so far.Over the past few years the washer has started "walking" when on the spin cycle. I replaced the shock dampeners but that didn't completely solve the problem.Over the past six months the washer has started howling during the spin cycles. Anyone with familiarity with machines would recognize that sound as bad bearings. And the sound was getting worse. I had to either fix or replace the washer. I investigated having the washer repaired professionally but was told by two repair services that it wasn't worth the cost.So I decided to repair it myself. I went into this repair with the mind set that the washer was toast and it had to be replaced. $30 for the bearings was a risk I was willing to take. I watched a few youtube videos and got started. It should be noted that the videos weren't all the same. They did things in different orders and in different ways. For example one video removed the drain hose completely from the bottom of the drum and another just disconnected one side.To complete this repair the drum has to be removed from the washer. Disassembling the washer to free up the drum was straight forward and went well. No issues. Removing the drum was difficult. It's heavy and awkward to handle. I needed a helper to lift it out and put it back. With the drum out I could take it apart and remove the stainless steel basket. The basket is the thing that rotates with your clothes. This is where things got very difficult for me. The basket has a drive shaft on one end that goes through the seal and bearings then connects to the rotor of the motor. The shaft is supposed to slide out of the bearings and the bearings should stay in the drum. This didn't happen for me.For me, the large bearing was galled onto the drive shaft by corrosion caused by water that passed by the deteriorated seal. I tried everything to remove the bearing including Kroil, a blow torch, hammers and prying. It wouldn't move. In desperation I borrowed a seven ton gear puller from O'Rielly's auto parts. This is what finally got the old bearing off. I needed a long breaker bar to tighten the puller. I had to wear protective equipment because I was afraid something was going to shatter. With everything I tried, removing the bearing took a few days of after work activity.Once the bearing was off, I cleaned the drive shaft with emery cloth to remove corrosion and then cleaned the housings in the drum that receive the new bearings. I put the bearings into my freezer overnight before installing them into the drum. This shrinks the bearings and makes them easier to install.From there it should have been a simple matter to put everything back together. And it was until it was time to install the rotor into the drive shaft. This step is right near the end of the reassembly process. There's a spline where the shaft plugs into the rotor but now it didn't fit. What I discovered was that the massive force from the puller had mushroomed the spline to the point that it was too wide to fit into the rotor. This is when depression set in. And it's when I got out my files and started working on the rotor and the shaft. Working slowly I removed enough material from both sides that I was able to get a press fit of the shaft into the rotor by using the rotor attachment bolt to force them together. From there I was able to complete the install.Overall the repair took a week to complete working nights after work. Three of those five days were spent on bearing and spline issues. And all that time my family was complaining that they couldn't wash their laundry. When I pointed them to a nearby laundromat, they decided to wait for me to complete the work.Now that the work is complete I can honestly say that the washer is as good as new. It's quiet and as a plus, the washer doesn't "walk" around anymore. The worn bearings must have allowed the basket to vibrate enough to make the washer walk.Would I do this repair again, yes. But I'd wait unto my family was out of town ;).What would I do differently knowing what I do now? Instead of using the puller on the bearing, I'd have bought a cheap angle grinder at Harbor Freight and I'd have cut the bearing off. This would have prevented the spline from getting mushroomed.Now you know my story.

Had to fix LG front loader with a new bearing and seal went it pretty easy, had no trouble putting in the machine. Worked as it should to bring my wash machine back to life. Fit good and no noise to speak of. I put in freezer overnight to make installation easier, sound weird but it worked and went in very nicely

I used this kit to repair my LG Tromm washer, the job isn’t easy or fun but you can save a ton of money doing this repair, with all the tariffs it just didnt make sense to be buying a new machine in this economy - the parts fit well - but you have to take your time

** UPDATE **What a huge disappointment!!! These failed shortly after 3 years. I have to tell you, replacing bearing in a LG front loader is a real task, and that when you have ALL the right tools to do the job. The actual bearing pull & place is the easiest part for me. But having to pull the washer and completely disassembling / reassembling it is a royal pain. For me to have to redo this project because these bearing failed is a crime. And it's just my wife and I and we're not talking about a lot of weekly loads.These bearing failed because they are crap - period. You must look elsewhere, spend a few dollars more and get the OEM bearings. It is so well worth it.The original review is below FOR REFERENCE ONLY. DO NOT BUY THESE BEARINGS.==================================================================I just installed this set and it was a perfect fit for our 12 year old LG washer. Excellent fit and our first load is smooth and quiet. =FAILED AS ABOVE=It is easy to make a bearing that fits. I will let you know if this does not provide expected life. =FAILED AS ABOVE=Like I said... so far - so good. =FAILED AS ABOVE=

dimensions were perfect, went back together with ease and are nice and quiet.

These were semi-easy to install (nothing easy on a front loader), but remember to order the separate spider to extend the life of this kit!