Vestil FJB-150 Basement Floor Jack 150 In. Maximum Height 2,588 Lb. Capacity Red

Updated - The below mentioned issue with the pins was solved by purchasing the Fastener 014973159566 Swivel Hitch Pin, 3/4 x 4-1/4-Inch on Amazon. I paid $7.34 ea. and purchased eight for my two Vestil FJB-150 Floor Jacks. I have included the pics of the pins and they work and fit perfect. If you wanted to save some extra money you could also go to the local hardware and get Grade 8 3/4inch by 4 inch bolds and just drill a hole in the end and put in a R-Cotter pin.Purchased two of the Vestil FJB-150 Basement Floor Jacks and as far as the jack itself it is well made and for the price is of good quality BUT the major flaw is the pins that they supply with the jack is a joke. It is a approx. 5/8" diameter pin with a groove cut on each end. When you try to move the jack into place the pins can easily move out of the holes. It would have cost them nothing to just drill a hole in each end of the pin and supply a pair of Hitch Pins Clips or R Clip Cotter Pins to go into the holes which would keep the pins in place when moving or adjusting the jacks. Something that for a couple of cents would have made the jack a five-star item year round. Overall the jack is a good investment as long as you spend a couple of dollars to fix the pin issue that the manufacturer could not bother to do!

Best money I've spent. I have a second story deck so I needed something to extend over 12+ feet. (my other supports only extended to 8'). The deck is approaching 20 years old and in great shape, but being a 35' long by 12 wide deck 14 feet off of the ground and over a lower deck the same size, keeping an eye on the 8x8 supports is a yearly thing to be safe. Still "dead on level" after all of these years, 1 of my 8x8's on the corner has some minor splitting but also had a slight "bow to it" (the other supports don't get the weather as much as the exposed end support).I purchased 2 of these to support the corner on each side of the existing post to replace the corner 8x8. For safety, I did actually pour 2 piers below grade so they had a good base to support the deck while I removed and replaced the 14' tall corner support (and added a second one). These stayed in place prior to the replacement for months and did a fantastic job.

This is a very sturdy floor jack with a great adjustment range, making it useful for potentially many different projects. The ends tend to "walk" around the top and bottom surfaces when you attempt to tighten the big length adjustment screw, so plan on fastening the jack ends to both surfaces with 3/8" bolts. Holes are provided just for that purpose. I deduct one star because, as others have stated, the height setting pins fall out easily while you are trying to set the initial height (before pressure is applied). The 3/4" diameter hitch pins recommended by another reviewer DO NOT FIT THIS PRODUCT. I have ordered some 5/8" by 4+1/4" hitch pins (#014973159542) instead. Ideally, pins which cannot fall out would have been included with this product.

I looked at many different product options and this one seemed to be the best. After I received it and installed it, I can say this is a great support to use for problems with sagging beams. It is substantially heavy duty and you can easily fine tune the lift. The hardware is inside the tubes for shipping security. You will have confidence using this support.

We have a very old home and unfortunately the weight of so many added kitchen items was causing our floor to sag, resulting in the ceiling above to crack. We have several 6’ floor jacks in place in our basement but due to us adding a new hutch/pantry to our kitchen, the weight was just too much. We ordered the jacks late on a Friday night and they were delivered on Monday. Just to let others know, the pieces that go through the pipe to hold it in place are packaged and are inside one of the pipes. So make sure to look before fretting that they’re not there. Stood the pipe up and placed it under the beam and cranked it up, placing the plate of the pipe up tight under the beam. With an extra crank or two it helped lift the kitchen floor up, which it turn lifted the kitchen ceiling. I can breathe a sigh of relief. Thank you!

Using to push back a tilting garage and add sheer strength while under tension. Rod to turn jacking screw is the weak point, and maybe a fail-safe? It bent easily. Ended up using a small pipe wrench.. Will find other uses after this project is done..

I purchased one of these to stiffen up a spongy spot on a floor. It comes as 3 cylinders. The one I got, the inside and middle cylinder were "fused" together. Not sure if it was rust, dried paint, or just poorly sized. After much pounding (and cursing) I was finally able to separate the inner and middle cylinder so that I could line up the holes which is necessary to attain the proper length. Also, large patches of the paint fell off even before I started to abuse the device. That didn't concern me much. The other part did. Also, it's not "returnable". If you can prove it's defective, you may be able to get a refund or replacement thru the manufacturer, not from Amazon.

Item is better than expected. Very robust, simple to use and like title suggests, it’s a “proper job”