Yoaoo 2Pack Black 345 Emblems Badge Decal 3D Logo Nameplate Compatible with 300C Red

Strong 3M tape already on the emblem ready to go out the package! The stencils are already pre-cut The emblem itself is made very good the numbers are solid strong and vibrant in color. They are BOLD just like the OEM emblems are. Instillation is not to bad, just use the stencil once you pop the numbers out as a guide so you get the numbers straight.

I dont know if i got lucky or what. But i somehow got a set with matching hemi bages as well. Which is great because i was trying to find a set of black and red hemi badges but couldnt find any. I opened up the package and to my amzement they had matching hemi badges with it. These badges look great. Nice weight to them and i can tell they have a coating on them to protect them. Which is nice because usually sets of these from other companies have a plastic red peice thats glued into the badge which breaks apart over time

Good quality still have them on the car easy to apply

Great factory look

I'll never give a product 5 stars, so people don't think it's fake. This product is great. Installation is easy, you can even use the adhesive backing to align the numbers straight. It has been a week since I ordered this product. I took it through a car wash for the first time today, and they are still in place.

So far so good. Going to do a first wash in a few days, let’s see how the adhesive holds up. Here’s a little write up with 392 measurements. Installation was easy, I got measurements off a 392 Durango.(see bottom for measurements) Best way to get accurate measurements is use 3M automotive tape I paid 3.49 for thin 3M tape at my local auto parts Store, leveling was easy (as long as your tape is level and straight) it comes on a precut adhesive tape board that stretches the entire length of the number. Suggestions: Cut the centers out of the 5s, and 4s make sure you don’t cut anything else since it’s all pre cut. It makes installation a lot easier. I would recommend having a second person handy to get accurate measurements, leveling and installation. Tools: 3M automotive tape Surface cleaner Alcohol Leveler Tape measure or ruler 2nd person Straight edge or any sharp knife Clean surface with a quick detailer ( I used chemical guys quick detailer) to clean off any dirt or grime, use rubbing alcohol to remove any chemicals from paint. (Remember to re wax that area after a few days) 1st. Un peel the backings to the numbers only. Measure where you want to tape off. (recommended someone to hold the ruler or tape measure and a 2nd to put the tape on the correct area for accurate measurements. 2nd. carefully with a leveler put on top or bottom of the numbers (2nd person recommended to hold leveler or to hold the numbers) press firmly in the position you want with the entire adhesive only with the backing to the numbers off. 3rd. holding onto the numbers peel the existing un peeled portion of the adhesive tape off while pressing against the numbers to ensure they won’t lift. The adhesive tape will stick on the numbers leaving small gray spots, but it will come off easily. (After that press each number for about 5-10 seconds to ensure there is no lifting while removing the rest of the adhesive tape.) 4th. Un peel the 3M tape you used to measure the position of the numbers. Clean around the area to make sure there is no more adhesive tape or 3M automotive tape. There you have it. 392 measurement specs from dealer: 5 1/2 down from fender crease 2 9/16 from door gap

Nice work good

These seem to be very good quality, metal and painted. I don't think itis 3M adhesive but it seems fine. Do this and save aggravation. Cut out the tape in the small spaces of the 4 and 5 before you mount them. Otherwise you will spend alot of time picking out the paper and tape while not scratching your paint.

Very very nice quality Better quality then some oem badges I purchased directly from mopar

Does what I want it to do.

After winter, one winter. The red is peeling off. Not impressed anymore.

Perfect