Gifts for Men,Damaged Screw Extractor Set-Christmas Stocking Stuffers for Men Adults Him,Mens Gifts for Dad,Husband,Stripped Screws Nuts & Bolts Drill Bit Tools for Easy Removal of Rusty Broken Screw

My 4 wheeler brake fluid reservoir lid had three stripped screws. I ordered the screws and the stripped screw removal kit. In five minutes I had those screws out and they worked like a charm. I highly recommend this set for stripped out screws. Very easy to read instructions plus a nice case to hold them.

Not much to say — it works. Handy little kit for stripped or rusty screws. Quality is decent, sharp enough for most jobs, and the bits feel durable enough for light to moderate use. Not pro-level, but for the price and occasional need, it’s totally worth it. Good to have around just in case

This worked for me to get license plate locking screws off the truck. The beveled side worked the other side not much use kept the drill in reverse on low speed with lots of pressure. had to use a few sizes to get the. Out but it worked well.

Badly stripped Phillips head in metal. Tried wd40, ice, heat, dremel, drill, broke bits off it was so locked up. This worked like a charm. Hint: use a larger bit if the smaller one still doesn’t do the trick.

Why did you pick this product vs others?:I deal with stripped screws too much at work and have been really delayed because of them. I was very skeptical at first if this would really work. It not only really works, but works fast. I had 7 stripped screws today and this bit removed each screw in under 30 seconds. Without it I would have spent way too much time removing network equipment without damaging the network equipment I was removing. Best $8.00 I've spent.

I have an old Toyota Tacoma that I have been working on. I was removing one of the fenders when a small mounting screw head snapped off, leaving the remainder of the screw in the frame. I soaked the remaining bit of the screw and the hole with PB Blaster for a week, hitting it with spray at least once and sometimes twice a day.I felt like today was as good a day as any to try to get the screw out. I again soaked the remaining bits with PB Blaster, wiped away the excess, and attempted to sink the drill side of the #1 extractor bit into the screw. It spun, but had no impact. Not wanting to potentially snap off the bit, because I know how fragile they are, I switched to a left handed drill bit that was the same size as the #1 bit in the kit. After the hole was started and I saw that I was going in straight, I switched back to the drill side of the extractor bit and got it to sink into the hole, down to the stop on the bit collar. I flipped the bit over and attempted to extract.Using a drill on a slow speed, making sure not to put too much force behind it, I saw that the bit wasn't extracting, instead it was grinding away the metal stem of the screw. I applied slightly more pressure and saw that it was just grinding away more of the stem. I stopped with the #1 and switched to the #2 bit. This time to make sure that I wasn't going too fast, I used a 1/4 inch collar/guide on the bit and fit the other end of the guide onto an Allen wrench. Applying minimal pressure and turning about a quarter turn at a time, I finally got the #2 bit to bite. The bit was down inside the screw and decent amount. Since the #1 hadn't extracted and instead ground away some screw material, the #2 was seated really well in the screw body.Now with extractor seated and biting, hardly applying pressure, I pressed the allen wrench slightly to the left, and that's all she wrote.Now the extractor bit is buried in the screw, making the job infinitely harder since you can't drill through it.I read that a grinding bit in a dremel should be able to grind the extractor bit down and hopefully cause it to crumble. I just destroyed one grinder bit trying to get through it.Now I am looking at buying another "rescue bit" to remove the extractor bit that is broken off in the screw. I should have just left hand drilled the screw out as best I could. This thing is more of a headache than it's worth.

I stripped a torx screw on a pistol optic. I used this kit with my 18v Bosch cordless drill and it worked perfectly. After drilling into the head, the extractor bit delivered enough grip to break the screw free of the blue loctite I had applied to the threads when I had first installed and stripped the head of the small torx screw. I give it a 15 out of 10!!

Well I bought them to remove my old deck screws. The product did not work. But to be fair the old screws were in terrible shape. Some of the screws were practically disintegrated. I followed the instruction reversed drilled then reversed screwed but they just turned and caught no material. Probably should return them but for $10 it’s not worth it. AGAIN MY SCREWS were badly weathered so maybe in a different situation they might have helped.