BEARFORCE Pressure Washer Foam Cannon with 6 Adapters & 1.10mm 1.25mm Tips, Adjustable Snow Foam Lance Soap Gun for Power Washer 800~4000 PSI

I bought this kit assuming that one of the six adapters would fit my Portland 1750 PSI electric PW from Harbor Freight - it worked! I first tried it with the standard brass pressure screw in place - no good. According to the instructions your supposed to replace that screw with another one (enclosed in the kit) that works with PW’s below 2000 PSI - be sure not to screw it in all the way - it needs to have a little play in it. Voila! Thick beautiful foam after a few minor adjustments of the water and air apertures. I used chemical guys honeydew, 2 ozs per bottle, and it was just like the videos you see. The foam is thick and persistent, so you have plenty of time to work it with your cloth of choice to further loosen dirt and grime. You can adjust the dials to use the gun to rinse off the soap, but it’s so easy to switch the standard wand with this setup, I did that so I wouldn’t lose the adjustments I made at the beginning to get the foam just right.The only minor complaint is at first I struggled to understand how to install the brass screw, so I went to the enclosed links for the help videos. Unfortunately, all of the videos reside on a Chinese social app platform, and are difficult to access. I was finally able to track them down and figure things out- it was really easy once I understood.Given that the Portland PW is probably the least expensive on the market (around $99), this makes a great combination of this is your first foray into foam cannons.This company makes several models, and as I write this, this fully brass assembly is out of stock - but the performance from their other models that offer this particular adapter is probably similar - great value!

The media could not be loaded. Excellent amount of foam with the correct mixture. Wash first car with more than enough foam. Washed a second car (the one in the video) with less soap in the mixture until it ran out of soap (last couple seconds in video).Still learning the correct soap/water mixture for perfect results without wasting unnecessary soap.Excellent results for the first two washes out of the box!

The media could not be loaded. I buy this due to the trash foam cannon that comes with a Black and Decker washer, it fits ok but not a perfect fit so it come off if you don't hold it right. Other than that, great THIC foams and works great even with cheap car shampoo.

Have a very old Karcher that I got off my parents. Has to be at least 15-20 years old at this point, maybe older. I don't know the PSI rating on it, but it's small and does an ok job when needed for things (remove mildew from cement, wash a car, etc). Saw this and figured I'd give it a shot vs. buying a newer/non-Karcher machine.I swapped out the little steel nozzle piece for the brass one which it says is required for machines with lower PSI ratings. Figured that was the way to go.A couple things I really like so far in the 1 time I've used it...1) Lots of brass/metal vs. plastic. Connector to the Karcher unit is not going to just snap off.2) Ability to make adjustments easy. I could have shot the foam far, or come even closer/thicker to the car3) Amount of foam this sucker makes! It might be the combination of this plus the Chemical Guys watermelon foam I bought too. I really had low expectations that I'd get foam like most of the Youtubers get with high pressure equipt. and fancy/expensive snow foam attachments.4) Made this pretty easy to wash my car, it made so much foam that I just did a 1 bucket method vs. a 2. Car was loaded with foam like it was hit by a 1-2 inch snow blanket.

This is the complete kit you need to work with most electric pressure washers (and gas ones too)! I am using a AR Blue Clean 383, and with this foam cannon you need to change out the orifice with the smaller hole (brass and included in the kit) and then put on your quick connect.With this done, it make mountains of beautiful foam to clean your car. I am using Meguiar's Gold Class Shampoo because it is cheap and easy to find. I dilute it 1:10 and it works perfectly. No need to spend more than this one costs.This kit is a great value because it includes so many different adapters and pieces that you can probably attach it to about any pressure washer out there.Using the washer is great too. You can adjust from a wide spray of foam, to a higher pressure jet of foam to kick off tough dirt. Even wheel wells get clean with this without needing to scrub (for maintenance washes).

Not sure why this states “may fit AR pressure washer” but I assume it’s for legal reasons. I took a gamble after taking some measurements and I can confirm that this did “possibly fit” my AR Blue 527 pressure washer. Build quality seems good, foam took some tweaking to get right, may not be the best in the market, but I don’t know as this was my first foam cannon. Will say this option saved me quite a bit of money in trying to get adapters for other foam cannons and was $30 cheaper than buying one from AR directly.

I was sceptical a foaming cannon would work to clean without a sponge, but it worked pretty darn good.Works great with a blue clean baonette pressure washer.I used the chemical guys soap product .

This is the 2d one I have had to purchase in a short time due to the first failing quite early. It would not shoot foam. I liked it prior to the malfunction but cannot speak to its longevity.